THK TJU Instruction Manual Download

Page: 34 / 134

3. Wiring

How to wire

3-6

TNU

⿟

Wiring example of each driver controller

･

Connecting TDO will open the internal relay K1, and the TDO emergency stop switch is acti-

vated.

･

While TDO is not connected, the internal relay K1 is closed.

･

When TDO or the emergency stop of the CN4 (1) and (2) pins is input to TNU, the emergen-

cy stop is entered in all the driver controllers connected to the TJU.

･

To enter the emergency stop individually to each driver controller, install an emergency stop

circuit to each driver controller.

• Do not connect the driver controller TSC and TLC to the CN5 (1) pin (S1).

Doing so may disable the emergency stop and cause damage or fault.

• Be sure to set the DC of TNU, TSC, TLC, and THC to 0 V respectively.

Otherwise, the communication may not be established.

• To enter the emergency stop to THC, install an external relay and disconnect the CN5 (3) and (4)pins of the THC.

Important

24V

Control power
supply

Control

power

supply

CN4

CN1

CN3

CN5

Motor

power

supply

TNU

TJU

TSC/ TLC

TDO

Upper

Industrial Ethernet cable (straight)

TACnet
cable

TJU

CN2

24V

5 V DC

Microcomputer

Motor power

supply

100 V AC
Single phase, 200 V AC

THC

CN3

CN5

CN7

Control power

supply

(1)
(2)
(3)
(4)

(2)

(1)

(1)
(2)
(3)
(4)
(5)
(6)
(7)

(1)
(2)
(3)
(4)

24 V DC

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands