THK TJU Instruction Manual Download

Page: 91 / 134

Communication parameters

5-7

5. Operation and

Adjustment

TNU

◦

EtherNet/IP

No.

Parameter details

Detailed description

External network type

Applicable network type and name.

Online user setting not allowed.

IP Address

IP address setting

Subnet Mask

Subnet mask setting

DHCP

DHCP (IP address automatic allocation) setting

Communication speed

(EtherNet/IP)

Communication speed of EtherNet/IP

Default Gateway

Default gateway setting

No.

Parameter details

Unit

Default setting

Input range

External network type

IP Address

192.168.0.1

0.0.0.0 to

255.255.255.254

Subnet Mask

255.255.255.0

0.0.0.0 to

255.255.255.254

DHCP

Invalid

Invalid/Valid

Communication speed

(EtherNet/IP)

Mbps

Auto

Auto/10HDX/10FDX/

100HDX/100FDX

Default Gateway

0.0.0.0

0.0.0.0 to

255.255.255.254

1) If DHCP = Valid, unforeseen IP address changes may take place, so we recommend setting

DHCP = Invalid and setting IP addresses manually.

2) HDX half-duplex / FDX full-duplex

◦

DeviceNet

No.

Parameter details

Detailed description

External network type

Applicable network type and name

Online user setting not allowed

Communication speed

DeviceNet communication speed

No.

Parameter details

Unit

Default setting

Input range

External network type

Communication speed

bps

Autoband

125k/250k/500k/

Autoband

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands