manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 26

2. Installation

2. 

How to install

2-11

TNU

2-2

 

Installation

WARNING

 

⿟

TNU and TJU must be installed 

within the control panel and oper-
ated with the door closed.

Failure to do so may cause electric 
shocks.

 

⿟

Before installing or moving the 

product with the unit energized, 
shut off the main circuit power 
supply of the driver controller.

Failure to do so may cause an elec-
tric shock or malfunction that could 
lead to injury.

 

⿟

Place the emergency stop cir-

cuit that stops the operations of 
the product and disconnects the 
main circuit power supply of the 
driver controller in the event of 
emergency.

Failure to do so may cause the dam-
age of the product that leads to injury.

Obligatory

 

⿟

Install a safety device such as 

a breaker for wiring to prepare 
against short-circuit of the wiring 
connected to the TNU and TJU.

Failure to do so may cause an elec-
tric shock or fault.

Caution - 

Electrical shock

Obligatory

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands