manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 102

6. Setup tool D-STEP

3. 

Operation method

6-10

TNU

3-4

 

Alarm history display screen

(1)   Reset alarm 

: Reset the generated alarm.

(2)   History clear 

: Deletes the alarm history from TNU memory.

(3)   Update 

 

: Loads the alarm history from TNU memory to D-STEP.

For alarm contents, see the alarm list 

(-> P.8-2)

.

The alarm history saves 50 past alarms and power ON information.

3-5

 

Setting before communication with driver controller (Important)

•  From D-STEP, be sure to set the parameter No.48 TDO enable function to "Invalid" before performing the 

program edit and operation command of each driver controller.   

If it keeps "Valid", communication cannot be established. In addition, return back to "Valid" to do it from TDO.

Important

(3)

(2)

(1)

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands