THK TJU Page 92 Instruction Manual Download | Manualshive

Page: 92 / 134

background image

3.

Communication parameters

5-8

5. Operation and

Adjustment

TNU

3-2

Net device list

Type

Not connected

TSC

TLC

THC

Any

⿟

Set the driver controller to be connected to TNU.

This is set to "Any" upon shipping and communicates with all the 16 shafts. By setting a driver
controller connected to each ID, communication with shafts that are not connected can be omit-
ted to improve the communication performance.

Setting is performed using the setup tool D-STEP

(-> P.6-6).

Setting values can be selected from

the following items.
When not concerned with the type of driver controller connected, or when connecting to new
models in the future, "Any" can be selected.

Input Mode

IO

Simple

Half

Full

◦

Input Mode

Sets the input mode for the driver controller connected to each ID.
It is set to "IO" before shipment and input mode can be set for each ID.

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

«
...
90
91
92
93
94
...
»

Summary of Contents for TJU







































































































































Reviews:

No comments

Related manuals for TJU

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

Brand: UNITED Pages: 22

Brand: Hafele Pages: 82

Brand: Jabra Pages: 4

Brand: Parker Pages: 32

Brand: Rayrun Pages: 4

AeGIS 7000 Series

Brand: PACH & COMPANY Pages: 2

Brand: ValvTechnologies Pages: 20

Brand: Samson Pages: 56

Brand: EasyIO Pages: 17

Brand: Partizan Pages: 7

Brand: GADGETMONSTER Pages: 30

Brand: Climatisation Pages: 52

Brand: TECOM Pages: 8

Brand: Gecko Pages: 82

Brand: nano sensorics Pages: 6

RSF B mini Series

Brand: Harmonic Drive Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands