THK TJU Page 117 Instruction Manual Download

Page: 117 / 134

9. Maintenance and

Warranty

9-2

TNU

WARNING

Maintenance and inspection

⿟

Before conducting maintenance and inspection works, be sure to stop the machine and

shut off the power supply. Take security measures like locking, etc. to ensure any unau-
thorized person cannot turn the power ON.

Otherwise, injury caused by unexpected behavior may occur.

Obligatory

1-1

Periodical inspection

1-1-1

Periodical inspection of TNU and TJU

Perform the following inspection works once every 6 to 12 months.

Inspection items

Inspection Procedures

Actions

Cleaning of the

body unit

There shall be no dust, particles or oil content

adhered on the unit.

Clean it with cloth or the like.

Loose connector/
screw

There shall be no loose connectors or fixing

screws.

Securely re-connect or re-
tighten.

Abnormality of unit
parts

There should be no discoloration, damage or

disconnection due to heating.

Replace with new one.

1-2

Standard of durability of consumables for TNU and TJU

1-2-1

Standard of durability of consumables for TNU

⿟

Parts listed in the table below are subject to aged deterioration. The periods indicated in the
durability are only for reference.

Consumables

Location

Durability

Contact relay

TDO connection circuit (with TDO connected) 100,000 cycles

• We do not provide repair service for TNU and TJU out of the warranty period. Please prepare a spare TNU

and TJU in advance or purchase new ones.

Important

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands