THK TJU Page 107 Instruction Manual Download | Manualshive

Page: 107 / 134

background image

7. Digital Operator

TDO

7-2

TNU

1.

Introduction

1-1

Standard precautions

⿟

Duplication or reproduction of the whole or part of this manual without permission is prohibited.

⿟

Please note that the contents of this manual is subject to change without prior notice, due to im-
provements of the product or other reasons.

⿟

We have made all possible efforts to make the content of this manual accurate. However, if you
find any mistake or uncertainty in this manual, please contact us.

⿟

Some photo, screen display, outline drawing, or illustration in this manual may differ from actual
products.

⿟

If descriptions in this manual differ from the actual operation of the product, the actual operation
should be treated as correct, and THK shall not be responsible for matching the actual operation
with the description.

⿟

Note that THK shall not be liable for any result incurred by applying the product and this manual,
regardless of the reason.

⿟

Usage or operation of the product that is not described in this manual is prohibited.

⿟

Thank you for purchasing the digital operator TDO.

⿟

This manual describes the correct methods for handling and operating the digital operator TDO,
and precautions for this product.

⿟

Carefully read and understand this manual before using the product to safely and correctly han-
dle the product.

⿟

Be sure to keep this manual after reading it so that you can refer to it when needed.

⿟

Please visit THK technical support website (user registration is required) to check the latest man-
ual. URL: https://tech.thk.com/

⿟

Please ensure this document is provided to the end users.

⿟

This document contains the information only on TNU of TDO. Before using TDO, please make
sure to read the TDO Instruction Manual provided separately.

⿟

Note that you cannot confirm/change TNU parameter settings by TDO.

1-2

Saving programs and parameters (Important)

⿟

Please save programs and parameters in preparation for possible loss by failures or operation er-
rors of the driver controller and for fast recovery on the product replacement.

⿟

Use the setup tool D-STEP to save the data. Execute "Save" for "File" on the "PROGRAM" and
"Parameter" screens.

1-3

Limit for operation (Important)

⿟

You can perform "Program Edit" and "Parameter Edit" of each driver controller by TDO, but can-
not edit TNU parameters. To edit TNU parameters, use the D-STEP.

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

«
...
105
106
107
108
109
...
»

Summary of Contents for TJU







































































































































Reviews:

No comments

Related manuals for TJU

Brand: Lawler Pages: 5

Brand: Badger Basket Pages: 3

Brand: FrSky Pages: 2

traxon e:cue LCE-mx

Brand: Osram Pages: 35

Brand: DSEGenset Pages: 74

Brand: ITALFARAD Pages: 32

Brand: Baier Pages: 20

Brand: Penn Pages: 10

Brand: Therma-Stor Pages: 20

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

TRAP-SHUFFLE Game Simulator

Brand: RF SOLUTIONS Pages: 2

Brand: Hunter Pages: 2

Brand: jablotron Pages: 12

Tunnel Master Jr

Brand: ICS Pages: 70

SCENE MASTER - V1.0

Brand: JBSYSTEMS Light Pages: 24

Brand: CALEFFI Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands