THK TJU Instruction Manual Download | Manualshive

Page: 94 / 134

background image

6. Setup tool D-STEP

6-2

TNU

1.

Introduction

⿟

Thank you for purchasing the setup tool D-STEP.

⿟

This manual describes the correct methods for using, installing, and operating the PC setup tool
D-STEP.

⿟

Carefully read and understand this manual before using the product to safely and correctly han-
dle the product.

⿟

Be sure to keep this manual after reading it so that you can refer to it when needed.

⿟

Please visit THK technical support website (user registration is required) to check the latest man-
ual. <URL: https://tech.thk.com/>

⿟

Please ensure this document is provided to the end users.

⿟

This document describes only information related to TNU of D-STEP. For details of D-STEP, refer
to the instruction manual of D-STEP.

1-2

Saving programs and parameters (Important)

⿟

Please save programs and parameters of the driver controller in preparation for possible loss by
failures or operation errors and for fast recovery on the product replacement.

⿟

To save the data, use this software to execute "Save" for "File" on the "PROGRAM" and "Param-
eter" screens.

For more information, see the instruction manual of the D-STEP.

⿟

Duplication or reproduction of the whole or part of this manual without permission is prohibited.

⿟

Please note that the contents of this manual is subject to change without prior notice.

⿟

We have made all possible efforts to make the content of this manual accurate. However, if you
find any mistake or uncertainty in this manual, please contact us.

⿟

Some screen display and illustration in this manual may differ from actual products.

⿟

If descriptions in this manual differ from the actual operation of the product, the actual operation
should be treated as correct, and THK shall not be responsible for matching the actual operation
with the description.

⿟

Note that THK shall not be liable for any result incurred by applying the product and this manual,
regardless of the reason.

⿟

Windows XP, Vista, and 7 are the trademarks of Microsoft Corporation in the United States.

⿟

When changing TNU setting, use the latest version above D-STEP Ver 1.20.

1-1

Standard precautions

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

«
...
92
93
94
95
96
...
»

Summary of Contents for TJU







































































































































Reviews:

No comments

Related manuals for TJU

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Panasonic Pages: 45

Brand: Eaton Pages: 288

Brand: GBD Pages: 15

U1000 iQpump Drive

Brand: YASKAWA Pages: 26

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 2

Brand: YASKAWA SIEMENS Pages: 373

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: Vag Pages: 12

Brand: Ezodo Pages: 7

Brand: Heat & Cool Pages: 5

Brand: WABCO Pages: 3

VENMAR ADVANCED TOUCHSCREEN CONTROL

Brand: vanEE Pages: 4

Brand: GOAL ZERO Pages: 52

SmartStuff Series

Brand: TCP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands