manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 5

iv

Table of Contents

TNU

1.

 Introduction

 

7-2

1-1

 

Standard precautions

― ――――――――――――――――――――――

7-2

1-2

 

Saving programs and parameters (Important)

―――――――――――――

7-2

1-3

 

Limit for operation (Important)

― ――――――――――――――――――

7-2

2.

 Connection

 

7-3

2-1

 

Connect to TNU

――――――――――――――――――――――――――

7-3

2-2

 

Initial screen

― ――――――――――――――――――――――――――

7-3

2-3

 

Connect start screen

― ――――――――――――――――――――――

7-4

2-4

 

Connection failure screen

― ――――――――――――――――――――

7-4

2-5

 

ID selection screen

― ―――――――――――――――――――――――

7-4

1.

  Alarm lists

 

8-2

1-1

 

Alarm lists

― ―――――――――――――――――――――――――――

8-2

2.

  Causes and counter measures of alarms

 

8-3

2-1

 

Causes and counter measures of alarms

―――――――――――――――

8-3

3.

  Other troubles

 

8-5

3-1 

D-STEP cannot detect the driver controller

――――――――――――――

8-5

3-2 

  

The driver controller does not operate even with the lower-level 
communication authorization switch ON

― ――――――――――――――

8-6

3-3 

During DVC pressing operation, position data abnormality occurs

――――

8-6

3-4 

Driver controller input signal is slow

― ――――――――――――――――

8-6

3-5 

Even with driver controller input signal MANU set to ON,

 

operation from D-STEP, TDO is not possible

― ――――――――――――

8-6

7. Digital operator TDO

7-1

8. T
roubleshooting

8-1

6. Setup tool D-STEP

6-1

3.

  Operation method

 

6-5

3-1

 

Connect start screen

― ――――――――――――――――――――――

6-5

3-2

 

Net device list setting screen

― ―――――――――――――――――――

6-6

3-3

 

Parameter setting screen

――――――――――――――――――――――

6-7

3-4

 

Alarm history display screen

― ――――――――――――――――――

6-10

3-5

 

Setting before communication with driver controller (Important)

――――

6-10

3-6

 

Offline edit screen selection

― ――――――――――――――――――

6-11

3-7

 

Offline net device list setting screen

― ―――――――――――――――

6-11

3-8

 

Offline parameter setting screen

――――――――――――――――――

6-12

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands