manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 14

1-8

1. Introduction

5. 

Network type

TNU

5-1

 

CC-Link

The CC-Link is a serial-based open field network.
This network is operated by the non-profit organization CC-Link Partner Association (CLPA) and has 
the following features:
 

1. Achievement of the high-speed and stable I/O response

 

2. Efficiency promoted by wiring saving

 

3. Flexible responses to multivendors

 

4. High reliability realized by RAS (Reliability, Availability, and Serviceability) functions

For detailed information on CC-Link, refer to the documents issued by the CC-Link Partner Associa-
tion and instruction manual for the master device used.

5-2

 

EtherCAT

EtherCAT is an open field network compatible with Ethernet.
EtherCAT is an open network designed with the operating principle to realize the high-speed  
communication and the architecture suitable for motion control, such as a function that  
synchronizes between highly accurate nodes, featuring the simpler wiring compared to Ethernet 
without requiring a switching hub.
The structure is supported for the needs of decentralizing I/O devices including the safety. 
The single network design will also save the wiring within the devices. Not only speeding up,  
increasing the accuracy of the device control, or improving the device production cycle time,  
EtherCAT also helps you to lower the cost associated with device installation or maintenance,  
such as standardizing cable wiring or simplifying the assembly.

For detailed information on EtherCAT, refer to the documents issued by EtherCAT Technology Group 
and the instruction manual for the master device used.

5-3

 

EtherNet/IP

EtherNet/IP is a standard industrial Ethernet network which adopts the widely used Ethernet TCP/
IP protocol and has CIP (Common Industrial Protocol) installed as the control protocol at the  
application layer.
It is regulated by IEC Standard IEC 61158.
Making the most of its ability for rapid and wide-range communication of large volumes of control 
and monitoring data from the field, it promises improved operation rates and quality and reduced 
TCO.

For detailed information on EtherNet/IP, refer to the documents issued by the ODVA (Open De-
viceNet Vendor Association) and instruction manual for the master device used.

5. 

Network type

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands