manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 18

2. Installation

1. 

Check products

2-3

TNU

•  For any special type, check against the delivery specification documents.

Model

:TJU

Serial

:XXXXXXXX

1-2

 

Check the package contents of TJU

1-2-1

 

Check the model/type of the product

Check the model indicated on the product label * against the purchase information.

Model

(See the following)

Serial number

<Model configuration>
 

    TJU

(1) Model

TJU

: Branch unit TJU

1-2-2

 

Checking the type and number of TJU accessories

No cable is provided, so please separately prepare a cable.

* Prepare the cables between TNU and TJU , TJU and TJU by yourself.

1-2-3

 

Check the product for any damage or abnormality

After the checking, keep the product packed in the packaging box until the start of installation work.

(1)

Reference

Type of parts

Model

Qty.

Branch unit

* See the product label

1

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands