THK TJU Page 111 Instruction Manual Download

Page: 111 / 134

8. Troubleshooting

Alarm lists

8-2

TNU

1-1

Alarm lists

⿟

Alarm functions of TNU are as follows:

⿟

The method to check the alarm is described in

3-4 Alarm history display screen (-> P.6-10)

No.

Alarm name

Content

STAT LED

Net device list collapse

A value out of the setting range

is contained in the net device list

upon start-up.

Device error

TNU is out of order.

Rotary SW setup error

After the start-up, the rotary SW

was changed.

Upper-level communication error*

Timeout or communication error

was detected in the upper-level

communication.

TACnet communication error

(Lower-level communication error)

T i m e o u t o r c o m m u n i c a t i o n

error were detected in TACnet

communication.

: Red flashing

Alarm lists

* On the D-STEP screen, CC-Link, EtherCAT, EtherNet/IP or DeviceNet communication error and

TACnet communication error are indicated as, respectively, upper-level communication error and

lower-level communication error.

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands