manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 52

4-13

1. 

TNU functions

4. TNU functions

TNU

X102E(CMD_READY)

X102D(CMD_SEND_END)

Y100E(CMD_SEND)

X102C(CMD_ERROR)

Program No.(A)

X1020~1027(CMD_No.)

X1030~103F(Para_No.)

X1040~105F(Prameter)

Y1020~1027(CMD_No.)

Y1028~102B(CMD_No.)

Y1030~103F(Para_No.)

Y100C(TNU_PARA_SW)

Communication

(TNU -> Dri-Com)

Communication

(Dri-Com -> TNU)

ON
OFF

ON
OFF

ON
OFF

ON
OFF

ON
OFF

Command No.(A)

Parameter No.(A)

Axis No.(A)

Command No.(A)

(1)

(2)

(3)

(4)

Parameter

Output

Input

No.

Input

Output

Status

Remarks

(1)

TNU parameter SW 

ON  

Command No. (0x24)  

Axis No.

Parameter No.

-

-

Parameter readout is 

only enabled when 

TNU is in PC mode

(2)

Command 

transmission switch 

ON

Command ready OFF  

Parameter No.

-

(3)

-

Command reply 

complete ON  

Parameter

-

(4)

Command 

transmission switch 

OFF

Command ready ON  

Command reply 

complete OFF

-

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands