manualshive.com logo in svg

THK TJU, Instruction Manual

Share
Download
THK TJU Instruction Manual Download Page 8

1. Introduction

1-2

TNU

1-1

 

Acknowledgment

Thank you for purchasing our product.
This product is a communication unit to connect the THK driver controllers TSC, TLC, and THC to 
industrial networks. We hope our products contribute to your further prosperity.

1-2

 

About this manual

1-2-1

 

Intended audience

The person in charge of designing embedded systems of the product and installing, wiring, and 
maintaining the product, and the person who actually uses the product.

1-2-2

 

Using This Manual

This manual describes correct handling methods and precautions for the product.
For the maximum performance and long life of the product, carefully read and understand this man-
ual to safely and correctly use the product.
If you access our website or use the printed version of this manual, be sure to keep it in the place 
that the intended audience can refer to it when needed.

1-2-3

 

Notice and attention

 

z

Do not use or handle the product in the ways that are not described in this manual.

 

z

Do not reproduce, reprint, or lend the whole contents or a part of this manual without permission.

 

z

Please note that description in this manual is subject to change without prior notice in the future, 
due to improvements of the product or other reasons.

 

z

We have made all possible efforts to make the content of this manual accurate. However, if you 
find any mistake or uncertainty in this manual, please contact our Customer Support (refer to 
back cover).

 

z

Drawings show representative examples, and may differ from your product.

 

z

Note that THK shall not be liable for any result incurred by applying this manual, regardless of the reason.

 

z

This manual can be applied to special types. However, the descriptions defined in the delivery 
specification drawings or the delivery specification documents of those special types should take 
precedence over this manual.

* Special types represent the products that have different materials and specifications from those 

of the standard products on catalogs.

1-2-4

 

Notation of this manual

1. 

Introduction 

•  Notes that can lead to unsatisfactory functions, error, or damage of the product if not observed while using 

the product.

Important

•  Reference information for the description.

Reference

•  Supplementary information for the description.

Note

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands