Sun Microsystems UltraSPARC-I User Manual Download Page 83 | Manualshive

Page: 83 / 410

background image

Sun Microelectronics
68

UltraSPARC User’s Manual

6.9.11 I-/D-Demap Page (Type=0)

Demap Page removes the TTE (from the specified TLB) matching the specified
virtual page number and context register. The match condition with regard to the
global bit is the same as a normal TLB access; that is, if the global bit is set, the
contexts need not match.

Virtual page offset bits <15:13>, <18:13>, and <21:13>, for 64Kb, 512Mb, and 4M
bpage TLB entries, respectively, are stored in the TLB, but do not participate in
the match for that entry. This is the same condition as for a translation match.

Note:

Each Demap Page operation removes only one TLB entry. A demap of a

64 Kb, 512 Kb, or 4 Mb page does not demap any smaller page within the
specified virtual address range.

6.9.12 I-/D-Demap Context (Type=1)

Demap Context removes all TTEs having the specified context from the specified
TLB. If the TTE Global bit is set, the TTE is not removed.

6.10 MMU Bypass Mode

In a bypass access, the D-MMU sets the physical address equal to the truncated
virtual address; that is, PA<40:0>=VA<40:0>. The physical page attribute bits are
set as shown in Table 6-16.

Bypass applies to the I-MMU only when it is disabled. See Section 6.7, “MMU Be-
havior During Reset, MMU Disable, and RED_state,” on page 54 for details on
the use of bypass when either MMU is disabled.

Compatibility Note:

In

UltraSPARC

the virtual address is longer than the physical address; thus,

there is no need to use multiple ASIs to fill in the high-order physical address bits,
as is done in SPARC-V8 machines.

Table 6-16

Physical Page Attribute Bits for MMU Bypass Mode

ASI

Physical Page Attribute Bits

CP

IE

CV

E

P

W

NFO Size

ASI_PHYS_USE_EC
ASI_PHYS_USE_EC_LITTLE

1

0

0

0

0

1

0

8Kb

ASI_PHYS_BYPASS_EC_WITH_EBIT
ASI_PHYS_BYPASS_EC_WITH_EBIT_LITTLE

0

0

0

1

0

1

0

8Kb

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
81
82
83
84
85
...
»

Summary of Contents for UltraSPARC-I



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for UltraSPARC-I

Brand: DBM Pages: 50

Brand: Javad Pages: 35

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

Brand: Commell Pages: 9

Brand: CAP-XX Pages: 8

Brand: ICP DAS USA Pages: 62

Brand: Airlink101 Pages: 46

Brand: TRENDnet Pages: 12

Bluespoon 17-1000

Brand: Radio Shack Pages: 1

Brand: ANEP Pages: 48

Brand: ZALMAN Pages: 18

Brand: Procool Pages: 2

Brand: RR-Concepts Pages: 12

Brand: Omron Pages: 14

Brand: silicom Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands