manualshive.com logo in svg

Sun Microsystems UltraSPARC-I, User Manual

The Sun Microsystems UltraSPARC-I user manual is available for free download from manualshive.com. This comprehensive manual provides detailed instructions on how to operate and maintain the UltraSPARC-I processor. Gain valuable insights on maximizing the performance of your system with this essential manual.

Share
Download
background image

Sun Microelectronics

337

Pin and Signal Descriptions

E

E.1 Introduction

This Appendix describes the UltraSPARC pins and signals in a general way. Con-
sult the relevant data sheets for detailed information about the electrical and me-
chanical characteristics of the processor, including pin and pad assignments. The
“Bibliography” on page 363 describes the available data sheets and how to obtain
them.

E.2 Pin Descriptions

E.2.1 UltraSPARC Data Buffer (UDB) Interface Pins

Table E-1

UltraSPARC Data Buffer (UDB) Interface Pins

Symbol

Type

Name and Function

UDB_UEH

I

Asserted when the High UDB is driving EDATA<127:64>, and it has detected an uncor-
rectable ECC error in that data. Synchronous to system clock.

UDB_UEL

I

Asserted when the Low UDB is driving EDATA<63:0>, and it has detected an uncorrect-
able ECC error in that data. Synchronous to system clock.

UDB_CEH

I

Asserted when the High UDB is driving EDATA<127:64>, and it has detected and cor-
rected a single-bit error in that data. Synchronous to system clock.

UDB_CEL

I

Asserted when the Low UDB is driving EDATA<63:0>, and it has detected and corrected
a single-bit error in that data.

UDB_CNTL<4:0>

O

These pins are connected to the UltraSPARC data buffer chips and control the flow of data
between the UDB registers and UltraSPARC. They are asserted with valid EDATA when
UltraSPARC is driving data to UDB. They are asserted the cycle before the UDB should
drive data to UltraSPARC. Synchronous to system clock.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for UltraSPARC-I



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for UltraSPARC-I

GE D20MX User Manual preview
D20MX
Brand: GE Pages: 146
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Brand: Supermicro Pages: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Brand: Time domain Pages: 64
Campbell NL115 User Manual preview
NL115
Brand: Campbell Pages: 38
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
ZiLOG Z8018 Series User Manual preview
Z8018 Series
Brand: ZiLOG Pages: 317
Trend Micro R610 Series Quick Start Manual preview
R610 Series
Brand: Trend Micro Pages: 2
Apogee X-FireWire Card Owner'S Manual preview
X-FireWire Card
Brand: Apogee Pages: 32
IBM TSO/E REXX User Manual preview
TSO/E REXX
Brand: IBM Pages: 242
BOSER Technology HS-4703 Manual preview
HS-4703
Brand: BOSER Technology Pages: 78
Adaptec RAID 5085 Release Notes preview
RAID 5085
Brand: Adaptec Pages: 2
ICP DAS USA WF-2572M User Manual preview
WF-2572M
Brand: ICP DAS USA Pages: 26
V7 SCREENSHARE PRO User Manual preview
SCREENSHARE PRO
Brand: V7 Pages: 4
Citizen IF1-ET01 User Manual preview
IF1-ET01
Brand: Citizen Pages: 26
Paradox Magellan Systems User Manual preview
Magellan Systems
Brand: Paradox Pages: 40
Sanyo POA-MD17SDID - Projector Terminal Expansion Board Instruction Manual preview
POA-MD17SDID - Projector Terminal Expansion Board
Brand: Sanyo Pages: 4

Brands by name

Popular brands

Load more brands