Suez Sievers M500e Operation And Maintenance Manual Download Page 301

Page: 301 / 325

ARNING

AND

RROR

ESCRIPTIONS

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

301

5000

Error

Calibration

Verification

The instrument is unable to calibrate. Please contact Technical

Support or your local service provider.

Occurs during calibration protocols when a calibration calculation

cannot be performed due to attempting to perform an invalid math

operation.

5001

Error

Calibration

Verification

Calibration measurement is out of range

Occurs during TOC calibration protocols, when no measurement is

returned for one or more vials.

5800

Error

DI Pump

No current in the DI Pump was detected.

Occurs when the DI pump is on and the Analyzer detects a current

< 120 mA.

5802

Error

DI Pump

High current in the DI Pump was detected.

Occurs when the Analyzer detects an unexpectedly high current in

the DI pump:

•

The DI pump is

and the current > 500 mA

•

The DI pump is

off

and the current > 120 mA

5804

Error

IC/TC Valve

No current was detected in the IC/TC Valve.

Occurs when the IC/TC valve is actuated and the Analyzer detects

a current < 5 mA.

5805

Error

IC/TC Valve

The current detected in the IC/TC Valve is unexpectedly high.

Occurs when the Analyzer detects:

•

> 200 mA when valve is actuated

•

> 5 mA when valve is not actuated

5807

Error

DI Loop Fan

High current in the DI Loop Fan was detected.

Occurs when the fan is on and the Analyzer detects a current

> 200 mA.

6800

Error

UV lamp

UV lamp failed.

6901

Error

IC sample pump

No current in the Sample Pump motor was detected.

Occurs when the pump is on and the Analyzer detects a current

< 60 mA

6902

Error

IC sample pump

High current in the Sample Pump motor was detected.

Occurs when the Analyzer detects:

•

> 1000 mA when the pump is on

•

> 60 mA when the pump is not on

6903

Error

Sample Pump

No motion on the Sample Pump motor was detected.

Occurs when the pump is running but no motion is detected with

quadrature encoder.

Warning/

Error

Name

Description

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands