Suez Sievers M500e Operation And Maintenance Manual Download Page 148

Page: 148 / 325

PGRADING

IRMWARE

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

148

Click inside the

Enter Activation Code

field and use the alphanumeric keypad

to enter the activation code provided by SUEZ. The feature appears in the

Features To Be Activated

area.

To install the feature shown, click

Apply

. A confirmation message appears.

Click

Yes

to continue. The Activations dialog box closes and the system adds

the feature shown to the Analyzer.

Upgrading Firmware

IMPORTANT:

System constants, Analyzer settings, and a Database Backup must be

saved before upgrading Analyzer firmware. See

“Saving System Constants” on

page 140

“Saving Analyzer Settings” on page 144

, and

“Backing Up the Database” on

page 167

for instructions.

Use these instructions to install firmware updates:

•

“To upgrade firmware using a USB memory device” on page 148

•

“To upgrade firmware through a network connection” on page 150

To upgrade firmware using a USB memory device

1. Power cycle the Analyzer and before re-starting, insert the USB memory

device (with the firmware update) into the USB port.

Navigate to the

Analyzer Settings

panel (

Settings

screen >

Instrument

Settings

tab).

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands