Suez Sievers M500e Operation And Maintenance Manual Download Page 174

Page: 174 / 325

RCHIVING

THE

ATABASE

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

174

Specify the number of months of history data to retain in the Analyzer’s

database.
For example, on 15 December 2020, a user archives the database and retains

months of history data. The Analyzer retains all history data from

15 October 2020 through 15 December 2020. History data older than

15 October 2020 is removed from the Analyzer’s database. All history data

(including history data older than 15 October 2020) is included in the backup

file.

Click

. A progress bar appears. When the archive is complete, the backup

file appears in the

Available Backups to Restore

section. A message appears

stating that the database was successfully archived and the Analyzer’s’

firmware must be restarted.

Click

to restart the Analyzer’s firmware. When the initialization process is

complete, the

Home

screen appears.

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands