Suez Sievers M500e Operation And Maintenance Manual Download Page 133

Page: 133 / 325

ONFIGURING

OCAL

ETTINGS

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

133

Click

Apply

to display the search results.

In the Protocol Record section of the screen, select a protocol. The results of

the analysis appear, with the Summary tab active and tabs for the results of

individual vials available for review.

Use the buttons along the bottom of the screen to

Print

Export

the results.

You can also

Print All

Export All

results in the Protocol Record section.

ETTINGS

CREEN

ETTINGS

CREEN

— S

YSTEM

ETUP

Configuring Local Settings

This section includes instructions for configuring settings for the local environment and

display formats.

To configure the environment settings

Define the Analyzer name and location, service provider, and system language, or

leave the default values. Also, use this instruction to set the system clock.
1. On the

Settings

screen, select the

System Setup

tab.

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands