Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 84 | Manualshive

Page: 84 / 225

Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 84

Commissioning

84

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

5.15.2.3 Disconnect hydraulic brake system

  1.  Apply the parking brake of the machine.
  2.  Uncouple the hydraulic sleeve (Fig. 52/1).
  3.  Slip the hydraulic sleeve onto the machine's blanked-off connecting piece (Fig. 52/2).

5.15.3 Parking brake

The applied parking brake secures the unhitched machine against rolling. The parking brake is

actuated via spindle and cable when turning the crank handle.

  (1)  Crank handle; in adjusting position (2)
  (2)  Adjusting position
  (3)  Resting position; swivelled by 180°

compared to the adjusting position

Fig. 53

Release parking brake

Ensure that the cable does not rest on or chafe against other vehicle

components.
With the parking brake released, the cable shall slightly sag.

1. Swivel the crank handle (1) from resting position (3) by 180° to adjusting position (2).
2. Turn the crank handle anticlockwise until the cable (5) is relieved.



The parking brake is released.

3. Swivel the crank handle to resting position.

Apply parking brake

Correct the setting of the parking brake if the tension path of the

spindle (4) is no longer sufficient.

1. Swivel the crank handle (1) from resting position (3) by 180° to adjusting position (2).
2. Turn the crank handle clockwise.



The parking brake is applied via the cable (5).

«
...
82
83
84
85
86
...
»

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments