Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 177

Page: 177 / 225

Service and maintenance of machine

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

177

12.7.2 Check/Retighten tension of roller chain for pick-up drive

Check the tension of the roller chain at the chain tensioner every day.
The roller chain must be retightened if the distance between washer

and sleeve of the chain tensioner is more than 8 mm.

1. Lower the pick-up to working position.
2. Secure tractor and machine against

accidental starting and rolling.

3. Unscrew the counter nut (1) by means of an

open-end wrench (wrench size SW 24).

4. Turn the hexagon nut (2) such that the

distance between washer (3) and sleeve (4)

is less than 8 mm.

5. Tighten the counter nut.

Fig. 103

12.8

CFS drum

WARNING

Risk to people of being crushed, drawn in and becoming

entangled due to unsecured powered driving elements!

Powering of the pick-up is not allowed with the side protector opened

and/or the protective casing of the pick-up removed. Fix the protective

casing of the pick-up properly to the machine and close the right-hand

movable side protector before operating the machine.

12.8.1 Bleed friction and compensating clutch of CFS drum

The friction and compensating clutch must be bled before the first

start-up and after longer downtimes to ensure its proper functioning.

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews:

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 177 / 225

Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews: