Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 40

Page: 40 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

Order number and explanation

Warning signs

87010270

Please read and observe the operating and safety instructions before

commissioning!

87007120
Risks when carrying out work on the machine such as mounting, adjusting,

trouble-shooting and maintenance, due to accidental starting or rolling of

tractor and machine!

This risk may cause most serious injuries or even death.



Secure tractor and machine against accidental starting and rolling before

carrying out any work on the machine.



Read and observe the instructions in the respective chapters in the operating

instructions depending on the work to be carried out.

87007104
Risk to any part of the body of being crushed if people stand within the

swivelling range of the tailgate!

This risk may cause most serious injuries or even death.



People are not allowed within the swivelling range of the tailgate as long as

the tractor engine is running with the propeller shaft coupled/the hydraulic

system connected.



Make sure that people leave the swivelling range of the tailgate before

opening the tailgate.

87007110
Risk to any part of the body of being crushed due to necessary work

underneath unsecured, suspended loads or lifted machine parts!

This risk may cause most serious injuries or even death!
Activate the safety locking mechanism against accidental lowering of suspended

loads or lifted machine parts before entering the hazardous area.

87007117
Risk to any part of the body of being drawn in or becoming entangled due to

powered working tools!

This risk may cause most serious injuries or even death.
Never enter the cargo space as long as the tractor engine is running with the

propeller shaft coupled/the hydraulic/electronic system connected.

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews:

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 40 / 225

Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews: