manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 79 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 79

 

Design and function

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

79 

 

 

5.15.1.2  Dual-line compressed-air brake system with hydraulic automatic load-sensitive brake 

pressure (ALB) regulator 

 

 

Tandem chassis 

  

WARNING 

 

Risk due to insufficient braking ability of the machine if the 

travelling height of the hydraulic levelling system has not been 

properly set! 

The hydraulic levelling system properly triggers the hydraulic ALB 

regulator only with the travelling height properly set. 
Check the travelling height of the hydraulic levelling system every day 

and readjust it if necessary. 

 

  

  (1)  Feed line with hose coupling (red) 
  (2)  Operating element for release valve (can 

only be actuated in uncoupled condition): 

 

push in as far as it will go and the 

service brake system releases, e. g. 

for manoeuvring the unhitched 

machine 

 

pull out as far as it will go and the 

machine is braked again by means of 

the system pressure coming from the 

air reservoir 

  (3)  Brake line with hose coupling (yellow) 
  (4)  Blank connection for brake line 
  (5)  Trailer brake valve with release valve 
  (6)  Diaphragm brake cylinder 
  (7)  ALB regulator (hydraulic), activated via the 

hydraulic levelling system of the tandem 

chassis 

  (8)  Hydraulic cylinders of the hydraulic levelling 

system 

  (9)  Compressed-air reservoir 
 (10)  Drain valve 
 (11)  Test connection, compressed-air reservoir 
 (12)  Test connection, diaphragm brake cylinder 
 (13)  Parking brake 

 

 

 

Fig. 47 

 

 

  

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments