Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 32

Page: 32 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13



Observe the maximum load capacity of the attached/hitched machine and the admissible axle

and tongue loads of the tractor! Run the machine with the cargo space being only partly filled if

necessary.



People are not allowed:



within the operating/hazardous area of the machine,



within the discharge area of the machine,



within the turning and swivelling range of movable machine parts,



beneath lifted and unsecured movable machine parts!



You are only allowed to operate powered machine parts if there are no people within the

machine’s hazardous area!



Secure the tractor against accidental starting and rolling before leaving it!



Safely support folded-up covers before standing underneath them!

Transport of machine



Before carrying out transport journeys, check:



the supply lines for proper connection,



the lighting system for damage, proper functioning and cleanliness,



the brake and hydraulic system for visible defects,



whether the parking brake has been completely released,



the brake system for proper functioning,



whether the required transport equipment, such as lighting, warning and protective devices,

has been properly mounted on the machine!



Check the braking effect before starting the journey! The tractor must produce the required

deceleration for the combination of tractor and attached/hitched machine!



Always ensure sufficient steerability and braking ability of the tractor!

Machines attached/hitched to a tractor and front or tail weights influence the driving

characteristics as well as the steerability and the braking ability of the tractor.



Observe the maximum loading capacity of the attached/hitched machine and the admissible axle

and tongue loads of the tractor!



Observe the broad overhang and the flywheel mass of the machine when cornering with

attached/hitched machine!



Set all movable machine parts to transport position and secure them before carrying out transport

journeys! Use the transport locks provided for this purpose!

3.4.2

Hydraulic system



Only an authorised workshop is allowed to carry out work on the hydraulic system!



Make sure that the hydraulic system on the tractor and on the machine has been depressurized

when connecting the hydraulic hose pipes!



Ensure to properly connect the hydraulic hose pipes!



Do not block any operating elements on the tractor, which serve to directly initiate hydraulic or

electrical movements of components, e. g. folding, swivelling and sliding operations!

The respective movement must automatically stop as soon as the operating element is released.

This shall not apply to:



continuous movements of devices,

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews:

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 32 / 225

Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews: