manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 44 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 44

Safety instructions

 

 

 

44 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

 

 

 

87010289 
Risk to any part of the body of being drawn in and becoming entangled due 

to powered working tools (pick-up and feeder rotor)! 

This risk may cause most serious injuries or even death. 

 

Keep sufficient safe distance to powered working tools. 

 

Never reach into the hazardous are of powered working tools as long as the 

tractor engine is running with the propeller shaft coupled/the hydraulic system 

connected. 

 

Ensure that people keep sufficient safe distance to powered working tools. 

 

 

 

 

 

 

 

3.6.2 

Instruction signs 

An instruction sign consists of a pictograph: 

  (1)  Pictograph including information about 

proper use of the machine. 

 

  The pictograph includes visual or 

descriptive information or information 

summarized in a table. 

 

 

 

Fig. 8 

 

 

 

87007132 
The required drive speed of the machine is 1000 min

-1

. 

Before switching the propeller shaft on, check whether the selected speed and 

sense of rotation of the tractor's p.t.o. shaft have been adjusted to the admissible 

speed and sense of rotation of the machine. 

 

 

 

 

87007133 

Observe the information for braking axle maintenance included in the operating 

instructions. 

 

 

 

 

87007134 
Risk due to improper cleaning of the machine. 

Absolutely observe the information in the chapter "Cleaning of machine", page 168 

when using a pressure washer/steam blaster for cleaning the machine. 

 

 

 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments