manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 175 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 175

 

Service and maintenance of machine

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

175 

 

12.6.9  Change gear lubricant oil 

 

 

  1.  Align the machine in horizontal position. 
  2.  Place a drip tray beneath the gearbox. The tray's capacity must at least be equivalent to the 

quantity filled in. 

  3.  Unscrew the oil drain plug. 

    The gear lubricant oil drains off. 

  4.  Unscrew the oil filling screw. 
  5.  Wait for the oil to stop draining out of the oil drain opening. 
  6.  Screw in again and tighten the oil drain plug. Use sealant. 
  7.  Fill the specified oil quantity in through the oil filler neck. 
  8.  Clean the oil filling screw and screw it in. 
  9.  Check the oil level after 5 service hours. The oil must be visible at the oil inspection plug. 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

12.7 

Pick-up 

 

 

WARNING 

 

Risk to people of being crushed, drawn in and becoming 

entangled due to unsecured powered driving elements! 

Powering of the pick-up is not allowed with the side protector opened 

and/or the protective casing of the pick-up removed. Fix the protective 

casing of the pick-up properly to the machine and close the right-hand 

movable side protector before operating the machine. 

 

 

12.7.1  Bleed friction clutch of pick-up 

 

 

The friction clutch must be bled before the first start-up and after 

longer downtimes to ensure its proper functioning. 

 

 

 

 

The easiest way to bleed the stuck friction clutch is to charge the 

machine with material to be loaded for a short time with the groove 

nut unscrewed such that the stuck friction clutch slips for a short time. 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments