manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 119 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 119

 

Operation

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

119 

 

 

 

7.2.3 

Functions and their symbols 

The following paragraphs show the symbols of the operating elements of the control set, their 

functions and the displays on the screen. 

 

 

Switch control set on/off 

 

 

 

At the same time, this key serves as emergency stop. After the 

control set has been switched off, all hydraulic functions are also 

switched off. 

 

  

  1.  Press the 

 key once. 

    The control set is switched on or off. 

 

  With the control set switched on, the 

Working

 menu appears on the screen. 

With the control set switched off, the display 

on the screen goes out 

  The screen shows: 
 

 

   

 

 

 

Switch road travel mode on  

 

 

 

The road travel mode can only be 

switched on: 

 

with lifted pick-up (attention, the 

pick-up is not checked for having 

been lifted completely), 

 

with lowered tailgate, 

 

with the transport floor stationary, 

 

with the dosing drums stationary. 

If these requirements are not fulfilled, 

a beep is emitted, a corresponding 

warning message and the non-fulfilled 

requirement in the 

Working

 menu 

appear: 
  (1)  Warning message 
  (2)  Pick-up down 
  (3)  Tailgate lifted 
  (4)  Transport floor powered 
  (5)  Dosing drums powered 

  The screen shows: 

 

 

 

 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments