Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 35

Page: 35 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13



Place the uncoupled propeller shaft on the respective holder!



Put the protective cover onto the p.t.o. shaft stub after the propeller shaft has been uncoupled!

3.4.5

Hitched machines



Only couple admissible combinations of tractor and hitched machine!



Observe the maximum admissible tongue load of the tractor at the coupling device in case of

single-axle machines!



Always ensure sufficient steerability and braking ability of the tractor!

Machines attached/hitched to a tractor influence the driving characteristics as well as the

steerability and the braking ability of the tractor, in particular single-axle machines with the tongue

load being exerted on the tractor.



Only an authorized workshop is allowed to adjust the height of the drawbar for drawbars with

tongue load!



Ensure sufficient tongue load at the support device when unhitching and parking a single-axle

machine!

Risk of tipping, particularly in case of unevenly charged machine (stability).

3.4.6

Brake system



The brake system of the tractor must be compatible with the brake system of the machine!



Immediately stop the tractor in case of a malfunction of the brake system. Have the malfunction

promptly remedied by an authorized workshop!



Only authorized workshops or qualified personnel are allowed to carry out adjustment and repair

work on the brake system!



Have the brake system regularly and thoroughly checked!

In order to maintain the operational safety, the wheel brakes must always be properly adjusted.



Before carrying out any work in the brake system:



safely park the machine and secure it against accidental rolling (chocks),



secure the lifted machine/machine parts against accidental lowering!



Especially beware when carrying out welding and drilling work and work involving open fire in the

vicinity of brake lines!



As a basic principle, test the brakes after any adjusting and maintenance work on the brake

system!

Compressed-air brake system



The compressed-air brake systems of the tractor and of the machine must be compatible!



Clean the sealing rings at the hose couplings of the feed and brake lines from possible soiling

before hitching the machine!



You are only allowed to start the tractor with the hitched machine moving when the pressure

gauge on the tractor indicates 5.0 bar!



Drain the air reservoir every day!



Cover the tractor's hose couplings before carrying out journeys without machine!



Hang the couplings of the feed and brake line on the provided blank connections with the

machine unhitched!

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews:

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 35 / 225

Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews: