manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 139 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 139

 

Operation

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

139 

 

daily transported loads counter are reset. 

  3.  Press the 

 key once. 

    The 

Working

 menu appears. 

   

 

 

7.2.9 

Sensor and state overview 

 

 

Sensor for 

Status 

1:  Cutting knives 

0:  Extended 

 

1:  Retracted 

2:  Cutting unit 

0:  Retracted 

 

1:  Extended 

3:  Steering axle locked 

0:  No response of sensor 

 

1:  Response of sensor 

    A short beep is emitted. 

4:  Steering axle unlocked 

0:  No response of sensor 

 

1:  Response of sensor 

5:  Forage wagon full 

0:  No response of sensor 

 

1:  Response of sensor 

6:  Tailgate lifted up to first opening width 

0:  No response of sensor 

 

1:  Response of sensor 

7:  Tailgate completely lifted 

0:  No response of sensor 

 

 

1:  Response of sensor 

8:  Tailgate completely lowered 

0:  No response of sensor 

 

1:  Response of sensor 

9:  Speed at dosing unit 

0:  No response of sensor 

 

1:  Response of sensor 

 

 

7.2.9.1  Call up state overview 

 

 

  1.  Press the 

 and 

 keys one after 

the other. 

    The display shows the 

Sensor and status 

overview

: 

  (1)  Sensor number 
  (2)  Sensor status 
  (3)  Number of sensor circuits 
 

  2.  Press the 

 or 

 key to display 

the next or preceding sensor. 

  The screen shows: 
 

 

   

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments