manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 58 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 58

Design and function

 

 

 

58 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

 

5.6.2.1  Crossover conveyor (optional extra) 

 

 

Forage wagons equipped with beaters can be 

fitted with the crossover conveyor for stable-

feeding or for charging the following conveying 

devices. 
The crossover conveyor (1): 

 

is mounted at the rear below the beaters, 

 

is powered by a hydraulic motor, 

 

can be powered in two driving directions. 

Depending on the driving direction, the 

green fodder is discharged on the right- or 

left-hand side of the forage wagon. 

The ISOBUS control set serves to 

 

switch the crossover conveyor on and off, 

 

change the driving direction. 

 

 

 

Fig. 27 

 

 

 

 

5.6.3 

Lock tailgate 

 

 

The tailgate can be locked via the stop-cock to 

secure it against accidental lifting and lowering. 
The stop-cock is positioned on the right-hand 

side of the tailgate. 
The table shows the meaning of the stop-cock 

positions. 

 

 

 

Fig. 28 

 

 

 

 

Stop-cock 

Tailgate 

Activity 

0 - closed 

lifted and locked 

trouble-shooting, cleaning, service and 

maintenance work 

I - open 

not locked 

lifting and lowering possible 

charging discharging 

 

 

 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments