manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 221 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 221

 

Circuit diagrams

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

221 

 

 

 

 

 

 

(A)  Extension module, ISOBUS control 
(B)  LIN module, ISOBUS control 
(C) Power unit, easy-to-use control 

 
  (1)  Crossover conveyor, cw rotation 
  (2)  Crossover conveyor, ccw rotation 
  (3)  Front grating 1 (optional extra) 
  (4)  Front grating 2 (optional extra) 
  (5)  Axle suspension 1 (optional extra) 
  (6)  Axle suspension 2 (optional extra) 
  (7)  No function  
  (8)  No function 
 
E1  Work lights, front grating 
E2  Work light, rear, left-hand 
E3  Work light, rear, right-hand 
E4  Work lights (optional extra) 
E5  Warning beacon (optional extra) 
E6  Work lights, front grating 
E7  Work lights, rear 

 

 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments