Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 165

Page: 165 / 225

Service and maintenance of machine

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

165

WARNING

Risk of crushing, shearing, cuts, amputation, becoming entangled,

wound up, being drawn in and risk of impact to people if:



lifted, unsecured machine parts accidentally come down or are

unintentionally lowered,



tractor and machine accidentally start and roll!



Secure lifted machine parts against accidental lowering before working

beneath lifted parts.



Secure tractor and machine against accidental starting and rolling

before carrying out any service or maintenance work on the machine.



Wait for the machine to stop completely before entering the hazardous

area of the machine.

WARNING

Risk to people of being crushed, drawn in and becoming entangled due

to unprotected powered driving elements during machine operation!



Start the machine only with the protective devices completely mounted.



It is not allowed to open protective devices:



when the machine is powered,



as long as the tractor engine is running with the propeller shaft

coupled/the hydraulic system connected,



if the ignition key is in the tractor and the tractor engine can be

accidentally started with the propeller shaft coupled/the hydraulic

system connected,



if tractor and machine have not been secured against accidental

rolling by means of their respective parking brake and/or the

chocks.

Close open protective devices before powering the machine.

WARNING

Dangerous situations may occur if load-bearing parts break due to

mechanical work on frame elements!

As a basic principle, the following is not allowed:



drilling at the frame or chassis,



boring up of existing holes at the frame or chassis,



welding on load-bearing parts.

WARNING

Risk of crushing and impact to people due to accidental lowering of the

machine lifted via the folding drawbar!

Secure the machine lifted via the folding drawbar against accidental lowering

before crawling into the hazardous area beneath the lifted machine.

WARNING

Risk of crushing and impact to people due to accidental lowering of the

lifted tailgate.

Secure the lifted tailgate against accidental lowering by means of the stop-

cock before entering the hazardous area beneath the lifted tailgate.

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews:

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 165 / 225

Search results

Summary of Contents for Super-Vitesse CFS 3101

Reviews: