SONIX SN32F755 User Manual Download Page 169

Page: 169 / 225

SN32F760 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 169

Version 2.0

5:4

PS[1:0]

Parity Select bits
00: Odd parity. Number of 1s in the transmitted character and the attached

parity bit will be odd.

01: Even Parity. Number of 1s in the transmitted character and the

attached parity bit will be even.

10: Forced 1 stick parity.
11: Forced 0 stick parity.

R/W

Parity Enable bit
0: Disable parity generation and checking.
1: Enable parity generation and checking.

R/W

SBS

Stop Bit Select bit
0: 1 stop bit.
1: 2 stop bits (1.5 if WLS bits=00). Must be 1 in Smart card mode.

R/W

1:0

WLS[1:0]

Word Length Select bits
00: 5-bit character length.
01: 6-bit character length.
10: 7-bit character length.
11: 8-bit character length.

R/W

14.11.10

USART n Modem Control register (USARTn_MC) (n=0,1)

Address Offset: 0x10

This register enables the modem loopback mode and controls the modem output signals.

Bit

Name

Description

Attribute

Reset

31:8

Reserved

CTSEN

CTS enable bit
0: Disable Auto-CTS flow control.
1: Enable Auto-CTS flow control.

R/W

RTSEN

RTS enable bit
0: Disable Auto-RTS flow control.
1: Enable Auto-RTS flow control.

R/W

5:2

Reserved

RTSCTRL

Source for modem output pin RTS.

R/W

Reserved

14.11.11

USART n Modem Status register (USARTn_MS) (n=0,1)

Address Offset: 0x18

This register is a read-only register that provides status information on USART input signals.



Note:

Whenever the CTS bit changes state, an interrupt is generated if the MODEM Status Interrupt is

enabled.

Bit

Name

Description

Attribute

Reset

31:5

Reserved

CTS

Clear To Send State.
Complement of input signal CTS. This bit is connected to USARTn_MC[1]
in modem loopback mode.

3:1

Reserved

DCTS

Delta CTS.
Set upon state change of input CTS. Cleared after reading this register.
0: No change detected on modem input CTS.
1: State change detected on modem input CTS.

Summary of Contents for SN32F755


































































































































































































































Search results

Summary of Contents for SN32F755

Reviews:

Related manuals for SN32F755

Brands by name

Popular brands

SONIX SN32F755, User Manual

Search results

Summary of Contents for SN32F755

Reviews:

Related manuals for SN32F755

Brands by name

Popular brands