Siemens ERTEC 200P Manual Download Page 319 | Manualshive

Page: 319 / 501

background image

Copyright © Siemens AG 2016. All rights reserved

319

ERTEC 200P-2 Manual

Technical data subject to change

Version 1.0

when UART error interrupt is asserted.

31dt3 <unused>

00000000h r

Reserved, do not modify, read as zero.

Register:

UARTTCR

Address:

80h

Bits:

31dt0

Reset value:

0h

Attributes: r (w)

Description:

Test control register
(for integration test)

Bit

Identifier

Reset

Attr.

Function / Description

0

ITEN

0h

r w

Integration test enable. When this bit is
1, the UART is placed in integration
test mode, otherwise it is in normal
mode.

1

TESTFIFO

0h

r w

Test FIFO enable. When this bit it 1, a
write to the UARTTDR writes data into
the receive FIFO, and reads from the
UARTTDR reads data out of the
transmit FIFO.
When this bit is 0, data cannot be read
directly from the transmit FIFO or
written directly to the receive FIFO
(normal operation).

2

SIRTEST

0h

r w

SIR test enable. Setting this bit to 1
enables the receive data path during
IrDa transmission (testing
requires the SIR to be configured in
full-duplex mode). This bit must be set
to 1 to enable SIR system loop back
testing, when the normal mode control
register UARTCR bit 7, Loop Back
Enable (LBE) has been set to 1.
Clearing this bit to 0 disables the re-
ceive logic when the SIR is transmit-
ting (normal operation). This bit de-
faults to 0 for normal operation (half-
duplex peration).

31dt3 <unused>

00000000h r

Reserved, unpredictable when read.

Register:

UARTITIP

Address:

84h

Bits:

31dt0

Reset value:

0h

Attributes: r(h) (w)

Description:

Integration test input read/set register
(for integration test)

Bit

Identifier

Reset

Attr.

Function / Description

«
...
317
318
319
320
321
...
»

Summary of Contents for ERTEC 200P






















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERTEC 200P

Brand: Echelon Pages: 40

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Lakeshore Pages: 186

REVOLUTION Pro Controller 2

Brand: Nacon Pages: 11

Brand: Nacon Pages: 18

Brand: Nacon Pages: 24

Brand: Nabco Pages: 35

Brand: Parkside Pages: 65

Brand: Vaillant Pages: 52

Brand: Vaillant Pages: 11

Brand: We Care Solar Pages: 46

Brand: Watts Pages: 4

OneFlow OFTWH-R

Brand: Watts Pages: 8

Brand: WABCO Pages: 4

Brand: Rayrun Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands