manualshive.com logo in svg

Sharp Blue Treak LH75400, User Manual, Page: 491 / 502

Share
Download
Sharp Blue Treak LH75400 User Manual Download Page 491

LH75400/01/10/11 (Preliminary) User’s Guide

Register Map

6/17/03

 26-11

26.13 SSP Registers

Base address: 0xFFFC6000

NOTE:

 All other address locations are reserved and must not be used during normal operation.

26.14 UART0 and UART1 Registers

UART0 Base Address: 0xFFFC0000
UART1 Base Address: 0xFFFC1000

Table 26-15. SSP Register Summary

NAME

ADDRESS 

OFFSET 

TYPE

RESET

VALUE

DESCRIPTION

CTRL0

0x000

RW

0x0000

Control Register 0

CTRL1

0x004

RW

0x0000

Control Register 1

DR

0x008

RW

0x0000

Receive FIFO (Read)/Transmit FIFO (Write)

SR

0x00C

R

0x03

Status Register

CPSR

0x010

RW

0x00

Clock Prescale Register

IIR/ICR

0x014

RW

0x0

Interrupt Identification Register (read)/Interrupt 
Clear Register (write)

RXTO

0x018

RW

0x000

Receive Timeout Register

///

0x01C - 0xFFF

Reserved

Table 26-16. UART0 and UART1 Register Summary

NAME

ADDRESS

OFFSET 

TYPE

RESET
VALUE

DESCRIPTION

DR

0x000

RW

0x---

Data read or written from the interface. It is 12 bits wide 
on a read and 8 on a write.

RSR/ECR

0x004

RW

0x0

Receive Status Register (read)/Error Clear Register (write)

///

0x008 - 0x014

Reserved

FR

0x018

R

0x00000090 Flag Register (read only)

///

0x01C - 0x020

Reserved

IBRD

0x024

R

0x0000

Integer Baud Rate Divisor Register

FBRD

0x028

RW

0x00

Fractional Baud Rate Divisor Register

LCTRL_H

0x02C

RW

0x00

Line Control Register, HIGH byte

CTRL

0x030

RW

0x0300

UART Control Register

IFLS

0x034

RW

0x12

Interrupt FIFO Level Select Register

IMSC

0x038

RW

0x000

Interrupt Mask Set/Clear Register

RIS

0x03C

R

0x00-

Raw Interrupt Status Register

MIS

0x040

R

0x00-

Masked Interrupt Status Register

ICR

0x044

W

Interrupt Clear Register

DMACTRL

0x048

RW

0x00

DMA Control Register

///

0x04C - 0x07C

Reserved

///

0x080 - 0x08C

Reserved

///

0x090 - 0xFFC

Reserved

Summary of Contents for Blue Treak LH75400























































































































































































































































































































































































































































































































Reviews:

No comments