manualshive.com logo in svg

Sharp Blue Treak LH75400, User Manual, Page: 325 / 502

Share
Download
Sharp Blue Treak LH75400 User Manual Download Page 325

LH75400/01/10/11 (Preliminary) User’s Guide

UART0 and UART1

7/15/03

 19-5

19.3 UART0 and UART1 Programmer’s Model

While UART0 and UART1 offer similar internal functionality to the industry standard 
16C550, the programmer’s interface differs. That information is covered here.

The base address for UART0 is:

UART0 Base Address: 0xFFFC0000

The base address for UART1 is:

UART1 Base Address: 0xFFFC1000

The following locations are reserved and must not be used during normal operation:

• 0xFFFC0008 through 0xFFFC0014

• 0xFFFC001C through 0xFFFC0020

• 0xFFFC004C through 0xFFFC007C

• 0xFFFC0080 through 0xFFFC008C

• 0xFFFC0090 through 0xFFFC0FFC

19.3.0.1 UART0 and UART1 Register Summary 

Table 19-1. UART0 and UART1 Register Summary

NAME

ADDRESS

OFFSET 

TYPE

RESET
VALUE

DESCRIPTION

DR

0x000

RW

0x---

Data read or written from the interface. It is 
12 bits wide on a read and 8 on a write.

RSR/ECR

0x004

RW

0x0

Receive Status Register (read)/Error Clear 
Register (write)

///

0x008 - 0x014

Reserved

FR

0x018

R

0x00000090 Flag Register (read only)

///

0x01C - 0x020

Reserved

IBRD

0x024

R

0x0000

Integer Baud Rate Divisor Register

FBRD

0x028

RW

0x00

Fractional Baud Rate Divisor Register

LCTRL_H

0x02C

RW

0x00

Line Control Register, HIGH byte

CTRL

0x030

RW

0x0300

UART Control Register

IFLS

0x034

RW

0x12

Interrupt FIFO Level Select Register

IMSC

0x038

RW

0x000

Interrupt Mask Set/Clear Register

RIS

0x03C

R

0x00-

Raw Interrupt Status Register

MIS

0x040

R

0x00-

Masked Interrupt Status Register

ICR

0x044

W

Interrupt Clear Register

DMACTRL

0x048

RW

0x00

DMA Control Register

///

0x04C - 0x07C

Reserved

///

0x080 - 0x08C

Reserved

///

0x090 - 0xFFC

Reserved

Summary of Contents for Blue Treak LH75400























































































































































































































































































































































































































































































































Reviews:

No comments