manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

9.6

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Protocols

SEL Fast Message Protocol

Note that no IED can support the transmission of all messages at all data 
speeds. If the selected data rate is not sufficient for the given message length, 
the IED will respond with an error message (see 

Fast Message Synchrophasor 

Settings

).

Some observations from 

Table 9.1

:

➤

A serial port set to 2400 baud or higher can handle any size 
message at any supported data rate.

➤

A serial port set to 1200 baud can handle any size message at 
any data rate, up to 30 messages a minute

➤

A serial port set to 300 baud can handle a single-synchrophasor 
message at 30 messages a minute, a four-synchrophasor 
message at 20 messages a minute, and any size message at 12 
messages per minute or less.

➤

A rate of 60 messages per minute requires 600 baud for single-
synchrophasor messages, 1200 baud for four-synchrophasor 
messages, or 2400 baud for any size message.

➤

A serial port set to any baud can handle any size message up to 
12 messages a minute.

Because it is a member of the SEL family of interleaved protocols, the SEL 
Fast Message Synchrophasor protocol is able to share the same physical port 
with separate data streams (see 

SEL Protocol on page 1.7

).

Fast Message Synchrophasor Settings

In the SEL Fast Message format, the SEL-2032 communications processor 
must request a particular data message period, which it embeds in its 
automatic enable message. If the requested message period is supported, the 
SEL IED will acknowledge the request and begin transmitting 
synchrophasors. If the requested message period is not permitted, the SEL 
IED will respond with an 

Invalid data

 error message and will not transmit any 

synchrophasor data.

The synchrophasor automatic message setting SP_RATE allows the SEL-2032 
to automatically Enable or Disable Unsolicited Data Transfer Messages to 
attached SEL IEDs over serial connections. The Enable Message contains the 
SP_RATE value instructing the attached SEL IED to begin sending 
“Unsolicited Write” (UW) Messages (synchrophasor data) back to the 
SEL-2032. See 

Automatic Message (SET A) Settings on page 7.11

 for a short 

description and valid settings for SP_RATE.

The SP_RATE setting will only be available if the attached device is an SEL 
IED, as indicated by the port DEVICE setting. It is available whether the 
attached SEL IED supports this functionality or not. If the SP_RATE is “N”, 
the SEL-2032 will not enable or disable UW messages.

If SP_RATE is anything other than “N”, the SEL-2032 will attempt to enable 
UW message transmission only if during autoconfiguration the IED indicates 
support for transmitting UW messages in its Fast Message Configuration 
response or the attached IED is one of the following:

➤

SEL-311A/B (R107 or higher)

➤

SEL-311C (R110 or higher)

➤

SEL-311L-1/-7 (R207 or higher)

➤

SEL-311L-0/-6 (R156 or higher)

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
ekwb EK-FC1080 GTX Ti TF6 Installation Manual preview
EK-FC1080 GTX Ti TF6
Brand: ekwb Pages: 2
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Brand: ZALMAN Pages: 9
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
Supersonic Franky Instruction Manual preview
Franky
Brand: Supersonic Pages: 46
Renesas Converter Board R0E521237CFK00 User Manual preview
Converter Board R0E521237CFK00
Brand: Renesas Pages: 6
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18

Brands by name

Popular brands

Load more brands