Schweitzer Engineering SEL-2032 Instruction Manual Download Page 175 | Manualshive

Page: 175 / 354

background image

7.27

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

User-Defined (SET U) Commands

that you configure the Fast Message client to periodically issue Enable
Unsolicited SER requests to an IED to restart the reporting of unsolicited SER
in case of loss of communications to the IED.

Transparent Connections

Before making a transparent connection, the SEL-2032 checks the NOCONN
bit on the Slave port. If the bit is asserted, the attempted transparent
connection is immediately aborted. In addition, the NOCONN bit blocks
transparent connections on every mechanism:

PORT

command, user-defined

transparent connect string (TRANS in

SET U

), and Distributed Port Switch

Protocol (LMD). If the PORT command is attempted, the following error
message is displayed:

Unable to connect, Port x blocked by NOCONN bit.

Virtual Terminal Connections

The SEL-2032 shall check the NOCONN bit before allowing any Virtual
Terminal connection.

When the VT connection is initiated by a SEL-2032 user via the

PORT

command, the SEL-2032 shall function exactly as described above for
transparent connections.

When the protocol card initiates a VT connection, the SEL-2032 shall reject
the connection as long as the NOCONN bit is asserted.

User-Defined (SET U) Commands

Use the

SET U

command to:

➤

Create user-defined commands that the SEL-2032 recognizes
and obeys.

➤

Enable handling of a recognized, but unsolicited, SEL relay
auto-message.

➤

Control the SEL-2032 command set.

User-defined commands allow the SEL-2032 to recognize unsolicited inputs.
You can create up to 11 user-defined commands for any Master port, including
8 general-purpose and 3 special-purpose commands. You can create up to 4
general-purpose user-defined commands on SEL IED and other IED ports.

The SEL-2032 has a predefined command set (e.g.,

SHOW

,

VIEW

,

SET

) that

allows you to control, interrogate, and set the SEL-2032 functions from your
computer. If a port is connected to an unattended device (e.g., an RTU or
substation computer), the SEL-2032 predefined command set may be
supplemented or replaced by user-defined commands that are appropriate for
the device and function. They are called user defined because you define the
command string and the action performed by the SEL-2032 when the
command is received by the SEL-2032. These commands are available at all
access levels.

Courtesy of NationalSwitchgear.com

«
...
173
174
175
176
177
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: Salusfin Pages: 6

Brand: Profile Pages: 6

iW-RainboW-G30D

Brand: iWave Pages: 89

Brand: Mitsubishi Pages: 874

Brand: Mellanox Technologies Pages: 57

Brand: IDT Pages: 207

Brand: Supero Pages: 16

PowerMatch ESPLink

Brand: Bose Pages: 2

Brand: B&B Electronics Pages: 17

Brand: Supero Pages: 53

Brand: LUX LUMEN Pages: 41

Brand: Air Live Pages: 2

Smartio CP-104UL

Brand: Moxa Technologies Pages: 2

Brand: Cooler Master Pages: 4

Brand: ADLINK Technology Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands