Schweitzer Engineering SEL-2032 Instruction Manual Download Page 125 | Manualshive

Page: 125 / 354

background image

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Section 6

Database

Introduction

The SEL-2032 Communications Processor database contains status
information and data collected from devices attached to the 16 rear
communication ports. There is also information associated with the plug-in
protocol card slots Port 17 and 18. This section describes the structure of the
database and the various ways data within the database can be accessed.

Database Structure

The SEL-2032 data area includes a database of 16-bit registers for each of the
16 rear communication ports and a database for each of the two plug-in
protocol cards. Each port database consists of up to 15 regions, including
Global (GLOBAL), Local (LOCAL), Unsolicited Message Buffer (BUF),
eight Data regions (D1–D8), three Archive data regions (A1–A3), and a User
region (USER). Global, Local, and User regions are available on all used
ports. The Unsolicited Message Buffer (BUF) and Data regions are available
on ports with SEL IED and other IED device types. The Archive data regions
are available on IED ports. The first Data region (D1) and Archive data region
(A1) are available on Master ports for use with the 20USER setting. See

Section 5: Message Strings

for more information.

illustrates the

overall database structure.

provides detailed information about each port’s database. More

detailed information about each region is located in

Region Descriptions on

.

Courtesy of NationalSwitchgear.com

«
...
123
124
125
126
127
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

DR-4100P Series

Brand: Idis Pages: 30

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: Hama Pages: 6

Brand: Seattle Computer Products Pages: 31

Brand: Moxa Technologies Pages: 2

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Vega Pages: 12

N-FXE 02B Series

Brand: Lantronix Pages: 10

Brand: FOR-A Pages: 37

Brand: Commell Pages: 18

Brand: Robotis Pages: 10

Wisenet XRN-6410DB4

Brand: Hanwha Techwin Pages: 118

Brand: R3 Pages: 48

Brand: National Datacomm Pages: 62

Brand: I-Tech Pages: 6

OPTI495XLC VL-BUS 3/486

Brand: A-Trend Pages: 16

Quantum Ultra Series

Brand: Extron electronics Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands