manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

xiii

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Preface

Manual Overview

Collect Data From Non-SEL Devices.

Section 1: Introduction and Specifications
Example 4: Collect Unsolicited Write (Synchrophasor) Data on 
page 3.19

SEL Application Guides

Provide Data to a Modbus Master.

Section 1: Introduction and Specifications
Example 6: Modbus Job Done on page 3.26
Port Configuration (SET P) and Communication Settings on page 7.2
Modbus RTU Protocol on page 9.8

Provide Data to a DNP 3.0 Master (Serial).

Section 1: Introduction and Specifications
Port Configuration (SET P) and Communication Settings on page 7.2
Serial Distributed Network Protocol (Serial DNP3) on page 9.27
Distributed Network Protocol 3.0 (DNP3) LAN/WAN on page 9.43

Provide Data to a DNP 3.0 Master (Ethernet).

Section 1: Introduction and Specifications
Distributed Network Protocol 3.0 (DNP3) LAN/WAN on page 9.43

Install Protocol Cards.

SEL-2701 Instruction Manual
SEL-2711 Instruction Manual

Upgrade Firmware.

Appendix B: Firmware Upgrade Instructions

Replace Battery.

Battery Replacement on page 10.5

Provide Ethernet Connections.

SEL-2701 Product Information Sheet
SEL-2701 Instruction Manual
SEL-2890 Product Information Sheet
SEL-2890 Instruction Manual

Use SEL-2032 as a Port Switch.

Intelligent Port Switch on page 1.2
Example 2: Using the SEL-2032 as a Port Switch on page 3.4
Port Configuration (SET P) and Communication Settings on page 7.2

Time Synchronize Relays.

Time Synchronization Source on page 1.2

SEL Relay Instruction Manuals
SEL-5801 Cable Selector Software (available at www.selinc.com) 

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Brand: Sun Microsystems Pages: 6
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Teac HD-35NAS User Manual preview
HD-35NAS
Brand: Teac Pages: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Brand: Maple Systems Pages: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Brand: NETGEAR Pages: 2
JYTEK PCIe/PXIe-6301 Series User Manual preview
PCIe/PXIe-6301 Series
Brand: JYTEK Pages: 46
Advantech 3718HG User Manual preview
3718HG
Brand: Advantech Pages: 68
Harman crown PIP Series Reference Manual preview
crown PIP Series
Brand: Harman Pages: 16
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Brand: BIIZZY Pages: 2
Vecow SPC-2845 User Manual preview
SPC-2845
Brand: Vecow Pages: 61
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
AXIOMTEK FAB118-14B5P7 Quick Installation Manual preview
FAB118-14B5P7
Brand: AXIOMTEK Pages: 2
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
Wavtech bassFREQ Owner'S Manual preview
bassFREQ
Brand: Wavtech Pages: 8
National Instruments PXI Express PXIe-1085 Series User Manual preview
PXI Express PXIe-1085 Series
Brand: National Instruments Pages: 89
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Brand: Acces I/O products Pages: 13
Jäger ADwin-light-16 Manual preview
ADwin-light-16
Brand: Jäger Pages: 54
ICP DAS USA ZT-2005-C8 User Manual preview
ZT-2005-C8
Brand: ICP DAS USA Pages: 60

Brands by name

Popular brands

Load more brands