Schweitzer Engineering SEL-2032 Instruction Manual Download Page 315 | Manualshive

Page: 315 / 354

background image

10.5

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Testing and Troubleshooting

Calibration

Refer to the

STATUS

command explanation in

Serial Port Communications and Commands

for more detailed

information.

*>>

STATUS <Enter>

COMMUNICATIONS PROCESSOR - S/N 95012004 Date: 10/31/01 Time: 13:46:43
FID



SEL-2032-R100-V0-Z000000-D20021222 FID



SLBT-2030-R103-V0-Z000000-D20010122

SELF-TESTS

RAM SRAM CODE ARCH EEPROM P.S. SET BATTERY
512 kb 1024 kb OK 1792 kb OK OK OK OK

IRIG-B Input: Absent
I/O Board: Absent

Port Status     Success Rate SET M Database
1 Active     100% None
2 Inactive     None
3 Inactive     None
4 Inactive     None
5 Inactive     None
6 Inactive     None
7 Inactive     None
8 Active     None
9 Active     None
10 Inactive     None
11 Inactive     None
12 Inactive     None
13 Inactive     None
14 Inactive     None
15 Inactive     None
16 Inactive     None
17 Sole Node(100h) NORM None
F Active     100% None

*>>

Figure 10.2

STATUS Command Screen

Calibration

Schweitzer Engineering Laboratories (SEL) performs a calibration of the
SEL-2032 clock at the factory. You do not need to periodically calibrate the
clock.

Battery Replacement

A battery maintains the clock (date and time) if the external DC source is lost
or removed. The battery is a 3 V lithium coin cell. At room temperature
(25°C), the battery will operate nominally for 10 years at rated load.

The battery experiences a low self-discharge rate when the SEL-2032 is
powered from an external source. If the source is lost or disconnected, the
battery discharges to keep the internal clock going. The battery cannot be
recharged.

CAUTION:

There is danger of

explosion if the battery is

incorrectly replaced. Replace only
with Ray-O-Vac

®

no. BR2335 or

equivalent recommended by
manufacturer. Dispose of used
batteries according to the
manufacturer’s instructions.

!

Perform the battery replacement procedure if the SEL-2032 reports a battery
failure. You will also notice that the time and date are incorrect. To change the
battery, perform the following steps:

Step 1. Remove power from the SEL-2032.

Step 2. Remove any cables connected to Port F of the SEL-2032.

Step 3. Remove the front-panel screws and front panel.

Courtesy of NationalSwitchgear.com

«
...
313
314
315
316
317
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Professional Series

Brand: PACOM Pages: 15

Brand: M86 Security Pages: 46

Brand: Cytron Technologies Pages: 13

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

PCard-E 021L-D5 Series

Brand: ORiNG Pages: 2

Brand: Lattice Semiconductor Pages: 43

ACCULINK 3161 CSU

Brand: Paradyne Pages: 19

Brand: Watchguard Pages: 21

Brand: ExtraHop Pages: 2

Brand: Altimium Pages: 12

Digital Loudspeaker

Brand: Dolby Laboratories Pages: 4

Brand: Amphenol Pages: 43

Brand: SilverStone Pages: 17

Brand: NI Pages: 8

Brand: LevelOne Pages: 61

Session SR-JV80-09

Brand: Roland Pages: 8

OG-HDTV-SDI-UHD

Brand: Opengear Pages: 7

GigaVUE H Series

Brand: Gigamon Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands