manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

8.16

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Set

After entering your new passwords, use the 

PAS

 command, as shown in 

Figure 8.25

, to view the new settings. The following example shows how to 

use the 

PAS

 command for viewing and setting passwords. When setting your 

passwords, be sure to choose “strong” passwords that cannot be guessed or 
broken easily with automated “password cracking” software.

*>>

PAS 1 <Enter>

New level 1 password: ? 

******

Verify new level 1 password: ? 

******

Level 1 password changed

*>>

PAS 2 <Enter>

New level 2 password: ? 

******

Verify new level 2 password: ? 

******

Level 2 password changed

*>>PAS <Enter>

1:Ot3579
2:Ta2468

*>>QUIT <Enter>

COMMUNICATIONS PROCESSOR - S/N 98205023   Date: 10/06/00  Time: 14:16:54

*

Figure 8.25

PASSWORD Change Sequence

If you are certain that your physical control of all access to the SEL-2032 is 
sufficient to prevent unauthorized access, or if the devices connected between 
the SEL-2032 and any other access points provide sufficient protection from 
unauthorized access, then you may disable password protection.

To disable passwords at a specific level, enter the keyword DISABLE instead 
of a password when setting the password.

The SEL-2032 sets the password and asserts the SALARM global element for 
approximately one second. In the SEL-2032, SALARM is assigned to 
ALARM by default, so the alarm contact will close for one second unless the 
ALARM setting has been modified. After entering new passwords, type 

PAS 

<Enter>

 to inspect them. Make sure they are what you intended, and record 

the new passwords.

If the passwords are lost or you wish to operate the SEL-2032 without 
password protection, install the Password Jumper (J17 B in the SEL-2032) on 
the main board (see 

Jumper Settings on page 2.1

 for jumper location). With no 

password protection, you and others can gain access without knowing the 
passwords and view or change active passwords and settings.

Using Strong Passwords

It is important that you establish strong password protection to safeguard 
against unauthorized persons setting or controlling your SEL-2032 and the 
devices attached to it. Strong passwords consist of at least six characters, with 
at least one special character or digit and mixed-case sensitivity, but do not 
form a name, date, acronym, or word. Passwords formed in this manner are 
less susceptible to password guessing and automated attacks. Examples of 
valid, distinct strong passwords include:

Ot3579

A24.68

Ih2dcs

4u-Iwg

Ic-4+

NOTE

: Do not use characters that 

you have selected as LMD prefix 
characters. See 

Section 9: Protocols

, 

for a description of LMD prefixes.

Used properly, passwords provide good protection against unauthorized 
access. Make sure you choose strong passwords and record them in a secure 
location. If your passwords are forgotten and lost, you will need to install the 
main board password jumper in order

 

to disable password protection long 

enough to view them with the 

PAS

 command.

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

GE D20MX User Manual preview
D20MX
Brand: GE Pages: 146
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Brand: IBM Pages: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 78
IBM 9040-MR9 Manual preview
9040-MR9
Brand: IBM Pages: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Brand: IBM Pages: 132
Pima ZEL508 Installation Instructions preview
ZEL508
Brand: Pima Pages: 4
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
Fostex DE-1 Service Manual preview
DE-1
Brand: Fostex Pages: 20
Teac HD-35NAS User Manual preview
HD-35NAS
Brand: Teac Pages: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Brand: Maple Systems Pages: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Brand: NETGEAR Pages: 2
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Brand: ZALMAN Pages: 8

Brands by name

Popular brands

Load more brands