Schweitzer Engineering SEL-2032 Instruction Manual Download Page 36 | Manualshive

Page: 36 / 354

background image

1.20

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Introduction and Specifications

Functions

Database Tools

The SEL-2032 command set contains several commands to help you check
that requested data are placed in the proper database location and to prevent
interference between data requests and responses.

AUTO

This SEL-2032 command provides a list of supported operate and “20”
commands on auto-configured SEL IED ports. Use this to confirm that the
desired commands exist for the relay you are using.

MAP

This SEL-2032 command provides a method to look at the structure and
addresses of a database region on a port-by-port basis or at specific regions
within each port’s database. When this command is applied to a port, the
SEL-2032 responds with a list of database regions, their data names, and the
number of archive records. Also use the

MAP

command to look at the

database structure within a region. When this command is applied to a region,
the SEL-2032 responds with a list of data item labels, their addresses, and the
type and number of data.

VIEW

This SEL-2032 database tool enables you to look at the data that are being
collected, parsed, and stored in a database region on a specific port. Several
variations of this command allow you to view all, part, or specific items within
the region.

TARGET

You can use the

TARGET

command to view the status of the SEL-2032

Global and Local elements and the status of any relay elements that are
received from an SEL relay. The relay elements will appear to be appended to
the Local elements. The

TARGET

command, like the SEL relay

TARGET

command, includes variations that permit you to request all elements or a
selected row of elements and to repeat the request automatically a specified
number of times.

CARD

Use the

CARD

command to display the value of the Control Input and

Control Output elements for the protocol card ports. Parameter

n

specifies the

port (17 or 18). Append the Bit Label flag BL to display the control bit labels.

STATUS

The

STATUS

command provides you with an overview of the SEL-2032

performance and a port-by-port analysis of communication and database
performance. Any problems with data collection or database delays occurring
in any specific region will be identified on this report. This information will
help you determine if data are being requested faster than can be
accommodated by the attached device, or if multiple requests are interfering
with each other. The status display also identifies ports in transparent
communication.

Courtesy of NationalSwitchgear.com

«
...
34
35
36
37
38
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

Brand: Lauterbach Pages: 61

Brand: Lattice Semiconductor Pages: 15

Brand: Zhone Pages: 1

Brand: RadiSys Pages: 44

Brand: Industrex Pages: 51

Brand: VCS Pages: 118

Brand: u-blox Pages: 29

Procont LMC-008-IO

Brand: janitza Pages: 28

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

SABVISION NVR32

Brand: SAB Pages: 29

Brand: Supero Pages: 16

Brand: CNC4PC Pages: 11

Brand: V-Count Pages: 2

DataFire GO! PRO

Brand: Digi Pages: 20

AdvancedTCA AT8901M

Brand: Kontron Pages: 76

Brand: McIntosh Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands