manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

9.43

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Protocols

Distributed Network Protocol 3.0 (DNP3) LAN/WAN

It is very important to note that the operation of this system depends on 
settings in the SEL-2032 as well as SER settings in the connected devices. It 
is, therefore, very important that you coordinate communications processor 
settings and relay settings carefully and ensure that when changes are made to 
the relay, that appropriate changes are made within the SEL-2032.

Distributed Network Protocol 3.0 (DNP3) LAN/WAN

Overview

The optional SEL-2701 Ethernet Processor with DNP3 allows the SEL-2032 
to support the DNP 3.0 Level 2 Slave protocol over an Ethernet connection. It 
can be used for data access and for control. For a complete description of this 
protocol, refer to the DNP Basic Four Documentation Set and the DNP V3.00 
Subset Definition, both of which are available from the DNP User's Group at 
www.dnp.org.

For information on DNP3 over a serial connection, see 

Serial Distributed 

Network Protocol (Serial DNP3) on page 9.27

.

Configuration

The DNP3 protocol settings that become available for DNP3 on the SEL-2701 
Ethernet port are shown in 

Table 9.25

. The DNP3 protocol settings are for the 

port assigned to the SEL-2701: Port 17 or 18. Keep in mind that any settings 
for the SEL-2701 DNP3 Ethernet port will not affect any DNP3 serial port 
configuration or operation and vice versa.

It may be useful to note a few parameters that are unique to configuring DNP3 
over Ethernet:

➤

The ENDNP setting allows the user to enable or disable all 
DNP3 sessions on the Ethernet interface.

➤

The DNPMAP setting enables the usage of custom DNP3 maps 
to define the data/control maps for the DNP3 sessions. The 
DNPMAP setting can have one of two values—AUTO or 
CUSTOM.

➤

DECPL indicates an exponential scaling factor, 10

DECPL

, to 

multiply by the raw value to calculate engineering units. Thus 
the default value of DECPL, 0, will still result in the raw value 
being multiplied by 1 (10

0

).

Up to 10 sets of unique master station parameters can be configured for 
implementation when the SEL-2032 communicates with a specified DNP3 
host. These parameters include: DNPIP

xx

, DNPTR

xx

, DNPUP

xx

, UNSL

xx

, 

PUNSL

xx

, DNPMP

xx

, and DNPCL

xx

, where 

xx

 is a master station number 

from 01–10. These allow you to specify, for all communication sessions with 
a particular master, whether or not to: 

➤

enable or disable unsolicited reporting at power up,

➤

enable or disable unsolicited reporting for normal operation,

➤

indicate which custom DNP3 map is associated with it, and

➤

enable or disable controls.

Note that although 10 masters are supported by the SEL-2701, only five 
unique configuration files are available. These mapping files follow the 
naming convention SET_DNP

xyy

.TXT, where 

x

 indicates the DNP3 map from 

1 to 5, and 

yy

 indicates the port number of the installed SEL-2701. These files 

reside in the SEL-2701 settings subdirectory and are associated with the 

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
EK EK-Quantum Momentum ROG Rampage VI Encore User Manual preview
EK-Quantum Momentum ROG Rampage VI Encore
Brand: EK Pages: 11
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Brand: Hauppauge Pages: 55
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Brand: Xyclop Pages: 19
Patton electronics 593/45 User Manual preview
593/45
Brand: Patton electronics Pages: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Brand: LevelOne Pages: 49
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
ZALMAN CNPS8900 Series User Manual preview
CNPS8900 Series
Brand: ZALMAN Pages: 10

Brands by name

Popular brands

Load more brands