manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

6.3

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Database

Database Structure

The Data regions D1–D8 and the Archive data regions A1–A3 store data 
solicited by messages you create with the automatic message (SET A) 
settings. The data you solicit using “20” messages are parsed automatically in 
the associated data region. All of the “20” message responses will fit in any of 
the Data regions, except the response to the 20EVENT, 20EVENTS, and 
20EVENTL messages. These messages elicit an event report from an SEL 
relay. Only the D3 and A3 data regions are large enough to hold an entire 
20EVENT or 20EVENTS event report response and only the A3 data region is 
large enough to hold a 20EVENTL event report response. Check the event 
size of newer relays to determine if they will fit in the available regions.

DANGER:

 Disconnect or 

de-energize all external 

connections before opening this 
device. Contact with hazardous 
voltages and currents inside this 
device can cause electrical shock 
resulting in injury or death.

!

You control the size of the data solicited with non-“20” messages based on the 
parsing method you choose and the size of the message response you define 
with the NUM

x

 setting. If you specify a size larger than the region size, the 

SEL-2032 will respond immediately with an “Out of Range” message.

The Data and Archive data regions of Ports 17 and 18 are controlled by the 
installed protocol card. Refer to your protocol card instruction manual to 
determine if, and how, these regions are used by the protocol card.

You can only reference those portions of regions that have data assigned. If 
you reference an address that is not assigned, the SEL-2032 will respond with 
a message that the data address does not exist.

You can allocate all, or a portion, of the User region with the 

SET A

 

command, or the 

SET M

 command will automatically allocate the User 

region. You must use the 

STORE

 command, user-defined write command, or 

Modbus

®

 write function code to put the data into this area. You may also use 

SET M

 to establish automatic storage of data into the User region.

Archive data regions are structured differently from other regions. Where all 
other regions contain only a single record, the Archive data regions contain a 
queue of records. From a data access point of view, the Archive data regions 
appear to only contain the oldest record. However, as soon as it is cleared, the 
next oldest record appears. The number of archive records that can be stored is 
only limited by the amount of nonvolatile Flash memory. See 

Archive Data 

Regions on page 6.21

 for more information.

The nonvolatile nature of these data regions, combined with the unique 
capability to contain multiple records, make them ideally suited to long-term 
data collection and storage. You can use the 

VIEW

 command to view the data 

associated with any record in the Archive data region queue; all other 
commands read only the oldest record. See the memory calculation procedure 
in 

Appendix D: System Planning Sheet

 for more information.

The SEL-2032 assigns Data and Archive data regions alternate labels or 
names based on the data they store. For instance, if you use the 20METER 
message to collect and store SEL relay meter data in Data region D1, that 
region is assigned the alternate label “METER.” Use the 

MAP

 command to 

view a list of regions on a port and any alternate labels associated with some 
of the regions.

You can also use the 

MAP

 command to show the detailed structure of any 

region.

Data 
Storage Formats

Data are contained within the SEL-2032 database in various formats. 
Character items and strings are stored with each character requiring one 
register but only using the lower byte of the register; the high byte is always 
zero. Any unused characters in a string are set to a value of zero. Integer items 
require a complete register. Real numbers are stored in IEEE single-precision 

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Mitsubishi 32172 User Manual preview
32172
Brand: Mitsubishi Pages: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Brand: Mellanox Technologies Pages: 57
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Brand: Watchguard Pages: 21
AMC DSP 88 User Manual preview
DSP 88
Brand: AMC Pages: 28
AMD -K6-2/450 - MHz Processor Application Note preview
-K6-2/450 - MHz Processor
Brand: AMD Pages: 98
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Brand: Promise Technology Pages: 148
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Brand: Patton electronics Pages: 80
IBM 55PUS8118 SCSI-2 Installation Manual preview
55PUS8118 SCSI-2
Brand: IBM Pages: 42
Icop VMXP-6453 User Manual preview
VMXP-6453
Brand: Icop Pages: 31
Acqiris SA240P User Manual preview
SA240P
Brand: Acqiris Pages: 89
Emerson Liebert ISWEBRT3 User Manual preview
Liebert ISWEBRT3
Brand: Emerson Pages: 28
Emerson PACSystems IC695CPE400 Quick Start Manual preview
PACSystems IC695CPE400
Brand: Emerson Pages: 37

Brands by name

Popular brands

Load more brands