Schweitzer Engineering SEL-2032 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 354

background image

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Preface

Manual Overview

This instruction manual will help you through all phases of your SEL-2032
Communications Processor application. This instruction manual will help you
understand how to design systems with the SEL-2032 and how to apply the
SEL-2032, and it provides a detailed reference to all commands, functions,
installation, and operation of the SEL-2032.

Revisions

We revise this instruction manual periodically as we enhance the SEL-2032. It
is important to use a version of this manual that is appropriate for the version
of your SEL-2032. Use

Appendix A: Firmware and Manual Versions

descriptions of SEL-2032 modifications and corresponding modifications to
this manual.

Manual Contents

Following is an overview of the sections in this instruction manual.

Safety Information and Warnings.

The back of the cover sheet contains

important safety information and warnings about applying this
product.

How to Use This Manual.

These pages provide information about manual

contents and conventions used in this manual.

Section 1: Introduction and Specifications

➤

SEL-2032 features and applications are introduced.

➤

The general topic of integration and how the SEL-2032 fits into
integrated systems are discussed.

Section 2: Installation

This section includes physical installation

instructions such as mounting drawings and jumper setup. Also
included is an explanation of how to power up, configure, and operate
the SEL-2032 in a simple example system.

Section 3: Job Done Examples

.

Examples of integration systems including

SEL-2032 configuration are presented.

Control Equations

This section explains how to write

SEL

OGIC®

control equation settings used in the SEL-2032.

Section 5: Message Strings

This section explains how to write special

message strings used in the SEL-2032.

Section 6: Database

This section explains the internal information storage

structure of the SEL-2032.

Section 7: Settings

This is a reference guide for SEL-2032 settings.

Section 8: Serial Port Communications and Commands

This is a

reference guide for SEL-2032 commands.

Section 9: Protocols

.

Protocols implemented in the SEL-2032 including

DNP3 and Modbus

®

are described.

Courtesy of NationalSwitchgear.com

«
...
11
12
13
14
15
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Vanguard Pages: 4

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Marconi OMS 1200

Brand: Ericsson Pages: 136

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: Lanner Pages: 59

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Brand: SSV Embedded Systems Pages: 17

Brand: Idis Pages: 22

Secure Site Manager 16

Brand: Black Box Pages: 16

Brand: Aviosys Pages: 77

Brand: Primera Pages: 82

Brand: LanReady Pages: 40

SteelCentral AppResponse 2170

Brand: Riverbed Pages: 166

IF1-WF 2 Series

Brand: Citizen Pages: 45

Brand: Dell Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands