Schweitzer Engineering SEL-2032 Instruction Manual Download Page 14 | Manualshive

Page: 14 / 354

background image

xii

SEL-2032 Communications Processor

Instruction Manual

Date Code 20120126

Preface

Manual Overview

Section 10: Testing and Troubleshooting

➤

This section explains how to test and troubleshoot SEL-2032
operation including initial checkout.

➤

This is a guide to SEL-2032 maintenance including firmware
upgrades and battery replacement.

Appendix A: Firmware and Manual Versions

.

This appendix lists and

describes all firmware versions as well as the changes for each release
of this instruction manual.

Appendix B: Firmware Upgrade Instructions

This appendix gives detailed

instructions for installing firmware upgrades.

Appendix C: SEL IED Compatibility

.

Consult this appendix for a list of SEL

relays and firmware versions that are compatible with the SEL-2032.

Appendix D: System Planning Sheet

Use this handy sheet to plan and

document your SEL-2032 installation.

Appendix E: ASCII Reference Table

This appendix is a guide to ASCII

characters and codes.

Quick Reference Cards.

This pull-out reference, printed on blue card stock,

lists SEL-2032 commands and SEL-2032 message strings.

Task Guide

The following paragraphs provide suggestions for which manual sections will
be helpful for specific tasks. In the electronic document form of this manual,
the items below are hyper-linked into the document to provide quick and easy
navigation.

If this is your first use of the SEL-2032 Instruction Manual, please review the
Safety Information and Warnings and this section. This information will
prepare you to perform the following listed tasks. This subsection also
contains references to additional documents not included in the SEL-2032
Instruction Manual, but available from SEL. Many of these documents are
available via our Web site at www.selinc.com.

Specify Part Number to Order an SEL-2032.

SEL-2032 Model Option Table (available at www.selinc.com)

Physical Installation.

Section 2: Installation
Initial Checkout on page 10.4

Learn How to Apply the SEL-2032 in a System.

Section 1: Introduction and Specifications
Section 3: Job Done Examples

Review Features and Specifications.

Section 1: Introduction and Specifications

SEL-2032 Data Sheet
SEL-2032 Product Information Sheet

Collect Data From SEL Relays.

Section 1: Introduction and Specifications
Section 3: Job Done Examples

Courtesy of NationalSwitchgear.com

«
...
12
13
14
15
16
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Alacritech Pages: 20

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Extreme Gaming VGA Cooler GV1000

Brand: ZALMAN Pages: 7

Brand: IDT Pages: 207

Brand: Idis Pages: 22

Brand: AMX Pages: 1

Brand: Promise Technology Pages: 26

Brand: Keysight Technologies Pages: 106

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

Brand: Renesas Pages: 6

FiberTwist XGS2410

Brand: Genexis Pages: 7

i.MX 8M Mini LPDDR4 EVK

Brand: NXP Semiconductors Pages: 20

Brand: Sony Ericsson Pages: 2

ibaBM-FOX-i-3o-D

Brand: IBA Pages: 13

Brand: Yeastar Technology Pages: 2

EK-Quantum Vector FE RTX 3080

Brand: ekwb Pages: 20

Brand: Altera Pages: 43

Brand: Cambium Networks Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands