manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

7.6

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Settings

Port Configuration (SET P) and Communication Settings

MSTR

Modem Startup String. 

If you use a modem, you must enter a modem startup string to
initialize the modem. The default string sets the modem to answer on 
four rings. You may set this number to match the needs of your 
modem and application, but, to match SEL-2032 expectations, there 
are a few modem settings that should not be modified:

The escape character must be “+”

The modem must be in verbal mode

The echo must be disabled

The X0 code set should be selected

The escape code guard time should be one second

See your modem instruction manual for details on your modem.

CD_CTS

Modem Carrier Detect
connected to CTS input (Y/N). 

If you are using an external modem which has its Data Carrier Detect 
(DCD) output connected to the SEL-2032 CTS input (such as with 
SEL-C222 cable), set this to Y. Otherwise, set it to N.

DCD_FLOW

Use DCD control line for flow control 
(Y/N).

If you are using an external modem on Ports 1 or 9 of the SEL-2032 
and connect the Data Carrier Detect (DCD) output of the modem to 
the DCD input (pin 1) of the SEL-2032, set this to Y. Otherwise, set it 
to N.

BAUD

Baud Rate (300; 600; 1200; 2400; 4800; 
9600; 19200; 38400). 

You enter the baud rate at which this port communicates.
Port F limits are 300–9600 bps. Only ports that are
designated as masters may use 38400 baud. Automatically set if 
auto-configured.

DATABIT

Number data bits (7, 8). 

You enter the number of data bits this port requires for
communication. Port F is fixed at 8 data bits with no parity or 7 bits 
with parity. 

Figure 7.2

 illustrates how this setting influences the 

EIA-232 character format.

STOPBIT

Stop bits (1, 2). 

You enter the stop bits this port requires for communication. Port F is 
fixed at 1 stop bit. 

Figure 7.2

 illustrates how this setting influences 

the EIA-232 character format.

PARITY

Parity (N, O, E, 1, 0). 

You enter the parity this port uses in communicating. Port F is
limited to parity options N (No), O (Odd), and E (Even). 

Figure 7.2

 

illustrates how this setting influences the EIA-232 character format.

RTS_CTS

Enable RTS/CTS handshaking (Y/N). 

You set to Y (Yes) to enable RTS/CTS handshaking. If LMD
Protocol, Modbus, or DNP3 is used, RTS/CTS control is not avail-
able. Instead, RTS is driven to control any external transceiver. For a
definition of RTS/CTS, see 

Data Flow Control on page 7.10

. With 

Modem set to Y (Yes) and CD_CTS set to Y (Yes), RTS_CTS control 
is not available.

SENDTIME

Send Date/Time synchronization
to Protocol Card (Y/N).

 

If the installed protocol card supports host-initiated time
synchronization, the Port settings include a SENDTIME
setting. This setting allows you to enable/disable host-initiated time 
synchronization of the connected protocol card. The only values 
accepted for this setting are “Y” and “N.” If the connected protocol 
card does not support the receipt of time synchronization commands, 
then the SENDTIME setting is hidden for the port.

XON_XOFF

Enable XON/XOFF flow control (Y/N).  You set to Y (Yes) to enable XON/XOFF flow control. If

PROTOCOL is set to binary, XON/XOFF flow control is forced to N 
(No). For a definition of XON/XOFF, see 

Data Flow Control on 

page 7.10

.

Table 7.1

Port Configuration (SET P) Settings Information 

 (Sheet 4 of 5)

Setting

Comment

Description

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
Garland P1GCCAS Installation Manual preview
P1GCCAS
Brand: Garland Pages: 4
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Danfoss TFX Installation And Operation Manual preview
TFX
Brand: Danfoss Pages: 61
XIA Pixie-4 Express Software Manual preview
Pixie-4 Express
Brand: XIA Pages: 17
Keithley PDISO-8 User Manual preview
PDISO-8
Brand: Keithley Pages: 71
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Brand: IEI Technology Pages: 136
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
ExtraHop 72 TB ESU Quick Start Manual preview
72 TB ESU
Brand: ExtraHop Pages: 3
Paradyne Hotwire 7996 User Manual preview
Hotwire 7996
Brand: Paradyne Pages: 46
Disc Makers ElitePro User Manual preview
ElitePro
Brand: Disc Makers Pages: 12
TL Audio IVORY 2 5052 User Manual preview
IVORY 2 5052
Brand: TL Audio Pages: 37

Brands by name

Popular brands

Load more brands