Schweitzer Engineering SEL-2032 Instruction Manual Download Page 221 | Manualshive

Page: 221 / 354

background image

8.5

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Serial Port Communications and Commands

Command Set

*>>

AUTO 1 <Enter>

FID: FID=SEL-151-R412-V656rp1rqys-D940901-E2
DEVICE ID: Example 21.6 kV Line
BAUD RATE: 9600
OPERATE SUPPORT:ASCII (1 Breakers, 0 Remote Bits)
COMMANDS SUPPORTED:
B 20METER
A 20DEMAND
B 20TARGET
A 20HISTORY
A 20STATUS
A 20BREAKER
A 20EVENT
A 20EVENTS

*>>

Figure 8.5

AUTO Command

BROADCAST

The

BROADCAST

command (Access Level 1) allows you to communicate

from one master port to all IED ports simultaneously. When you issue the

BROADCAST

command, the SEL-2032 will indicate the connected ports.

From then on, anything you enter will be sent to all connected ports.

Any messages from any of the connected IED ports will be sent to the single
master port, as long as they are framed with the <STX>/<ETX> characters. To
transfer binary messages, add an AAh byte after the <STX> character and
then a message length as the next byte. The SEL-2032 will use the message
length to determine the end of the message, instead of checking for an <ETX>
character.

Use the

BROADCAST

command with an R parameter to enter broadcast

communications in a receive-only mode. In this mode, master port messages
are used for connection termination only.

Exit broadcast mode by entering the transparent termination sequence defined
in the SEL-2032 master port settings. See

Transparent Communications on

for additional discussion on termination sequences. You will need to

allow an extra second for TERTIME1 due to some additional

BROADCAST

command delays. Note that the

BROADCAST

command is not supported for

virtual terminal master ports.

CAL

Use the

CAL

command (Access Level 2) to enter Access Level C. You need a

password unless the password disable jumper is installed (J17B in the
SEL-2032). Use the

PASSWORD

command at Level C to change passwords.

Figure 8.6

shows successful access.

*>>

CAL <Enter>

Password: ? ******

COMMUNICATIONS PROCESSOR-S/N 2007087055 Date: 01/20/12 Time: 11:52:44

WARNING: CALIBRATION level is for SEL authorized use only. Commands at this

level may disrupt device operation and cause the device to become
inoperable until returned to the factory for repair. SEL shall not be
responsible for any damage or liability resulting from unauthorized
access. Use the 2AC command to return to normal operation.

Level C
**>>

Figure 8.6

CAL Command

Courtesy of NationalSwitchgear.com

«
...
219
220
221
222
223
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Yamaha Pages: 4

SAFETank Series

Brand: Raidon Pages: 49

Brand: Teagle Pages: 40

Brand: GAMDIAS Pages: 15

Brand: vPipes Pages: 3

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

FieldPoint cFP-RTD-122

Brand: National Instruments Pages: 15

Brand: Hama Pages: 6

Brand: QNAP Pages: 54

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

Brand: Glacier Pages: 2

Brand: ZyXEL Communications Pages: 3

Brand: SriHome Pages: 12

Brand: Supermicro Pages: 131

Brand: Variscite Pages: 17

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands